How to Change Out Bathroom Faucet: A Step-by-Step Guide for Beginners
Learn how to change out a bathroom faucet in about two hours with basic tools. Follow these steps for shutoff valves, disconnecting lines, and installing a new
Updated November 2026
To change out a bathroom faucet, you shut off the water, disconnect the old supply lines and mounting hardware, set the new faucet in place, and reconnect everything with a leak-free seal. Most homeowners can finish a standard single-hole or three-hole swap in one to two hours with basic hand tools. The steps below cover prep, removal, installation, and testing.
Prepare the Sink Area Before You Start
Start by confirming the new faucet’s hole configuration matches your sink. Single-hole faucets fit one opening, while three-hole faucets need a spout hole and two handle holes spaced about 4 inches apart (center to center). Check the supply line connections too: most faucets use 3/8-inch compression fittings on the shutoff valves, though some use 1/2-inch threads.
Shopping for one? See our guide: Change Moen Bathroom Faucet Cartridge: 5 Best Replacements (2026).
Shut off the water at the angle stop valves under the sink. If the valves are stiff or do not close fully, shut off the main water supply to the house and open the faucet to relieve pressure before you work.
Remove the Old Faucet
- Place a towel or bucket under the sink to catch residual water.
- Disconnect the supply lines from the shutoff valves using an adjustable wrench or basin wrench. Hold the valve steady so it does not twist.
- Remove the mounting nuts on the underside of the sink. A basin wrench reaches these in tight spaces.
- Lift the old faucet out from above. If it is stuck from old plumber’s putty, loosen the seal with a plastic putty knife rather than a metal scraper to protect the sink finish.
- Scrape away old putty, caulk, and mineral deposits so the sink surface is clean and dry.
Install the New Faucet
Set the Gasket and Faucet
Most new faucets include a rubber gasket or mounting pad. Place it on the sink or the faucet base as the manufacturer specifies. Insert the faucet through the holes, then check that it sits level and faces forward before you tighten anything.
Secure the Mounting Hardware
From below, slide the washers and mounting nuts onto the threaded studs or shanks. Tighten evenly, alternating sides, until the faucet is firm. Overtightening can crack ceramic or stone sinks, so snug the nuts by hand and then add roughly a quarter turn with a wrench.
Connect the Supply Lines
Attach the hot and cold supply lines to the correct shutoff valves: hot on the left and cold on the right when you face the sink. Hand-tighten each connection first, then give it a final quarter to half turn with a wrench. Do not force compression fittings, because overtightening can deform the ferrule and cause leaks.
Test for Leaks and Adjust
Turn the shutoff valves back on slowly. Open the faucet to clear air from the lines, then check every joint under the sink for drips. Run hot and cold water for a minute each, and watch the supply connections and the base of the faucet. If you see a small leak at a compression nut, tighten it a little more; if it persists, disassemble and inspect the washer.
Recommended gear
- Basin wrench: Reaches mounting nuts in the cramped space under the sink, where a standard wrench cannot fit. View on Amazon
- Flexible braided supply lines: Make reconnecting to the shutoff valves easier and can be sized to match your new faucet’s fittings. View on Amazon
- Plastic putty knife: Removes old sealant without scratching the sink surface. View on Amazon
Common Mistakes to Avoid
- Skipping the water shutoff test. Confirm the valves stop flow before you disconnect anything.
- Mixing up hot and cold lines, which makes the handles work in reverse.
- Overtightening mounting nuts or supply fittings, which can crack the sink or damage seals.
- Buying a faucet with the wrong hole count for your sink without checking first.
- Leaving the faucet unchecked after installation. Test under pressure and recheck connections the next day.
For a faucet that drips after installation, Repair Dripping Faucet Bathroom: A Step-by-Step Guide for Beginners explains the most common causes. If you are choosing a new model, Bathroom Faucet Three Hole: How to Choose and Install One (2026) covers the hole setup in more detail, and Single Hole Faucet for Bathroom: 5 Best Picks Compared (2026) helps if you have one opening.
FAQ
How long does it take to change a bathroom faucet?
Most people finish a standard swap in one to two hours, including shutting off the water and testing for leaks. Older, corroded fittings can add time.
Do I need to shut off the main water supply?
Usually no, if the angle stop valves under the sink work properly. If they are stiff or leaking, shut off the main supply to be safe.
What if the shutoff valves won’t close?
Do not force them, because a broken valve can flood the room. Turn off the main water supply and consider calling a licensed plumber to replace the valves.
Conclusion
Changing a bathroom faucet comes down to careful shutoff, clean removal, and snug, even connections. Test every joint before you walk away. If anything feels beyond your comfort level, especially with corroded valves or water damage, consult a licensed plumber.
Related reading
- How to Replace a Bathroom Faucet: A Step-by-Step Guide for Beginners
- How to Fix a Dripping Bathroom Faucet: A Step-by-Step Guide for Beginners
Ready to choose one?
