We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Changing Faucet in Bathroom: A Step-by-Step Guide for Beginners

Learn how changing faucet in bathroom works, from shutting off water and removing the old unit to fitting and testing a new one. Clear steps for beginners.

Updated November 2026

Changing a faucet in a bathroom is a manageable weekend project for most homeowners. You will shut off the water, disconnect and remove the old faucet, fit the new one to the sink or deck, and test for leaks. Most single-hole and widespread faucets follow the same basic sequence, though fittings and mounting styles vary.

Before You Start: Check Your Mounting Style

Look under the sink before buying anything. Count the holes in the sink deck and note the spacing between them. A single-hole faucet needs one opening, a centerset faucet uses a 4-inch spacing, and a widespread faucet uses an 8-inch spacing with three separate pieces. Measure the distance from the center of the mounting holes to the wall so the spout will clear the backsplash. Check the supply line size too, since most bathroom faucets use 3/8-inch compression connections with 1/2-inch threaded tails.

Shopping for one? See our guide: 10 Best Wall Mounted Faucet Bathroom Options for Every Need (2026).

Removing the Old Faucet

Start by shutting off the hot and cold supply valves under the sink. Turn them clockwise until they stop. Then open the faucet to drain residual water and place a towel in the basin to protect the finish.

  1. Disconnect the supply lines with an adjustable wrench, holding the valve body steady so you do not twist the pipes.
  2. Loosen the mounting nuts beneath the sink. Some faucets use a plastic or metal retaining nut, while others use a mounting plate and bolts.
  3. Lift the old faucet straight up. If it is stuck from old plumber’s putty or sealant, slice around the base with a utility knife before pulling.
  4. Scrape the sink deck clean so the new gasket or mounting plate sits flat.

Installing the New Faucet

Set the new faucet in the holes and check its orientation before tightening anything. Many manufacturers recommend a thin bead of plumber’s putty or a rubber gasket between the deck and base. Feed the supply lines through the holes and fasten the mounting hardware from underneath, tightening evenly so the faucet sits level and does not rock.

Reconnect the supply lines to the shutoff valves. Hand-tighten first, then add a quarter turn with a wrench. Over-tightening compression fittings can crack the nut or damage the ferrule.

Testing and Final Checks

Open the shutoff valves slowly. Turn the faucet on at low pressure and run hot and cold water for about a minute each. Watch every connection for drips, then run the faucet through its full range of motion. If a fitting seeps, tighten it gently or check that the washer or O-ring is seated properly.

Tools and Supplies Checklist

  • Adjustable wrench and basin wrench
  • Utility knife and plastic scraper
  • Plumber’s putty or silicone-free gasket, if the manufacturer calls for it
  • Bucket and towels
  • Flexible supply lines, if the old ones are cracked or stiff

Common Mistakes to Avoid

  • Skipping the shutoff valve test. Always confirm the water is off before disconnecting anything.
  • Buying a faucet with the wrong hole spacing for your sink.
  • Overtightening plastic nuts, which can crack and cause leaks.
  • Forgetting to flush the new supply lines before attaching the aerator.
  • Leaving the faucet unsupported while tightening mounting hardware, which can strain the connections.

A basin wrench reaches the mounting nuts tucked behind the sink and saves a lot of frustration in tight cabinets. View on Amazon

Flexible stainless steel supply lines make connecting the new faucet easier and reduce the chance of leaks at the shutoff valves. View on Amazon

FAQ

Do I need a plumber to change a bathroom faucet?

Most homeowners can handle a faucet swap with basic hand tools. If the shutoff valves are corroded, leaking or do not close fully, consult a licensed plumber before proceeding.

How long does changing a bathroom faucet take?

For a standard single-hole faucet with accessible shutoff valves, many people finish in one to two hours. Widespread faucets and stubborn old fittings can take longer.

Can I reuse the old supply lines?

You can if they are flexible, unkinked and free of corrosion. Replacing them is inexpensive insurance against leaks, so many installers do it as a matter of routine.

Conclusion

Changing a bathroom faucet comes down to shutting off the water, removing the old unit carefully, and matching the new faucet to your sink’s hole spacing. Take your time with the connections and test for leaks before you call the job done. With the right tools and a clear plan, most homeowners finish the job without a plumber.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Kitchen Bath Channel.