Change a Bathroom Faucet: A Step-by-Step Guide for Beginners
Learn how to change a bathroom faucet in about two hours with basic tools. Shutoff, removal, install and leak-check steps for most sink faucets.
Updated November 2026
To change a bathroom faucet, you shut off the water supply, disconnect the old faucet’s supply lines and mounting hardware, set the new faucet in place, and reconnect everything with a leak check at the end. Most sink swaps take one to two hours for a first-timer. The process is largely the same for single-handle and widespread models, though the number of mounting holes you have matters.
Before You Start: Check Your Sink and Gear Up
Look at the existing holes in your sink or countertop. A single-hole sink takes a one-handle faucet, while three-hole sinks take widespread or centerset models. Measure the distance between the outer holes on a three-hole sink, since many widespread faucets are sized to a 8-inch center spacing. Confirm the new faucet’s supply line lengths match your setup, and note whether it uses a pop-up drain or needs a separate drain kit.
Shopping for one? See our guide: Change Moen Bathroom Faucet Cartridge: 5 Best Replacements (2026).
How to Change a Bathroom Faucet, Step by Step
- Close the angle stop valves under the sink. Turn them clockwise until they stop. If they are stiff or do not close, shut off the main water supply.
- Open the faucet to drain residual water and relieve pressure.
- Disconnect the supply lines from the shutoff valves using an adjustable wrench. Keep a towel and a small bucket underneath.
- Remove the drain assembly. Unscrew the pop-up linkage and the nut connecting the drain tailpiece, then pull the drain out if it is attached to the faucet.
- Loosen and remove the mounting nuts beneath the sink that hold the old faucet in place. A basin wrench reaches these in tight spaces.
- Lift the old faucet out and scrape away old plumber’s putty or sealant from the sink surface.
- Place the new gasket or rubber seal included with the faucet on the base, then lower the new faucet into the holes.
- From underneath, thread the mounting washers and nuts onto the studs and tighten them evenly by hand, then snug them with a wrench. Do not overtighten porcelain or stone sinks.
- Connect the supply lines to the shutoff valves. Hand-tighten first, then add a quarter turn with a wrench.
- Reinstall the drain assembly, following the manufacturer’s order for the pop-up rod or drain kit.
- Open the angle stop valves slowly. Run the faucet on hot and cold for a minute each, then check every connection for drips.
Checking for Leaks
Dry a joint with a paper towel and watch it for several minutes. Tighten a connection only a small amount at a time, because overtightening can crack a plastic nut or damage the washer.
Replacing Only the Cartridge Instead
If the new faucet is the same brand and style, you may only need a cartridge or valve replacement rather than a whole new fixture. Many owners find this quicker, since the body and supply lines stay in place. Check the model number and handle type before ordering, because cartridges are brand-specific. If you are working with a Moen model, the guide to Replace Cartridge in Moen Bathroom Faucet: 6 Best Picks Compared (2026) covers the common options, and Moen Bathroom Faucet Cartridge: 4 Best Replacements Compared (2026) explains how to match one.
Recommended Gear
- Adjustable wrench and basin wrench: A basin wrench reaches the mounting nuts behind the sink, which a standard wrench cannot. View on Amazon
- Plumber’s putty: It seals the base of the faucet to the sink surface and is easy to remove later. View on Amazon
- Bucket and towels: They catch the water left in the supply lines when you disconnect them. View on Amazon
Common Mistakes to Avoid
- Skipping the shutoff step and getting sprayed when the lines are disconnected.
- Overtightening mounting nuts on porcelain, which can crack the basin.
- Forgetting to scrape old putty, which prevents the new base from sealing.
- Buying a faucet that does not fit the number of sink holes you have.
- Cross-threading supply lines, which can cause leaks that only appear hours later.
FAQ
How long does it take to change a bathroom faucet?
Most first-time installers finish in one to two hours. A sink with stiff or corroded shutoff valves can add time.
Do I need to turn off the main water supply?
Usually no, if the angle stop valves under the sink work. If they leak or do not close fully, shut off the main supply to your home.
When should I hire a plumber?
If the shutoff valves fail, the drain is damaged, or the sink needs new holes drilled, consult a licensed plumber before continuing.
Conclusion
Shutting off the water, carefully removing the old faucet and sealing the new one are the core steps when you change a bathroom faucet. Take your time with the nuts and leak-check every joint before you walk away. A careful, methodical install will hold up for years.
Related reading
- Single Hole Faucet for Bathroom: 5 Best Picks Compared (2026)
- Single Handle Bathroom Faucet Moen Review: Key Features Explained
Ready to choose one?
