Changing Out Kitchen Faucet: A Step-by-Step Guide for Beginners
Learn how changing out kitchen faucet works, from shutting off water to connecting supply lines, with tools, common mistakes and a quick checklist.
Updated November 2026
Changing out a kitchen faucet is a manageable weekend job if you work methodically. You will shut off the water, remove the old unit, mount the new faucet, and connect the supply lines without leaks. Most swaps take one to three hours, depending on how cramped the sink base is and how stubborn the old connections are.
Before You Start: Check Fit and Gather Tools
Start by counting the holes in your sink deck. A single-hole sink takes a single-handle faucet, a three-hole sink takes a widespread or three-hole model, and many two-hole sinks take a centerset faucet. Check the mounting type too: deck-mount faucets sit on the sink top, while wall-mount faucets need a separate wall installation. If you are unsure which style fits, compare your existing faucet’s footprint and mounting hardware against the new listing before you buy.
Shopping for one? See our guide: Delta Tap Kitchen Faucet Review: Key Features Explained.
Gather these supplies before you begin:
- Adjustable wrench and basin wrench
- Plumber’s putty or a silicone gasket, depending on the faucet
- Bucket and old towels
- Flashlight or headlamp
- Flexible supply lines if the new kit does not include them
- Penetrating lubricant for corroded nuts
Step-by-Step: Removing the Old Kitchen Faucet
- Shut off the water. Turn the under-sink shutoff valves clockwise until they stop. Then open the faucet to drain the lines.
- Disconnect the supply lines. Place a bucket under the connections. Loosen the nuts with a wrench, holding the valve body steady so you do not twist the pipes.
- Remove the mounting hardware. Under the sink, unscrew the mounting nuts or release the clip-style brackets. A basin wrench reaches nuts that a standard wrench cannot.
- Lift out the faucet. Clean any old putty or gasket residue from the sink surface so the new faucet seals flat.
Installing the New Faucet Correctly
Read the manufacturer’s instructions first, since gasket placement and nut torque vary between brands. Many installers assemble the faucet body, gasket, and mounting plate on the bench before lowering it into the sink. Feed the supply lines through the holes, then tighten the mounting nuts evenly from underneath. Hand-tight plus a quarter turn with a wrench is typical for plastic nuts; over-tightening can crack the sink or the mounting plate.
Connect the supply lines to the shutoff valves, hand-tightening first and finishing with a wrench. Turn the water back on slowly and check every joint for drips while the faucet runs. If a connection weeps, tighten it a small amount rather than forcing it.
Check the Spray Head and Handle
If your new faucet has a pull-out sprayer, run it through its full range and confirm the hose retracts smoothly without kinks. Test hot and cold separately, then together, to confirm the cartridge or valve works in every position.
Common Mistakes to Avoid
- Skipping the shutoff test. Confirm the valves are closed before loosening any nut.
- Over-tightening plastic mounting nuts, which can crack and cause leaks later.
- Reusing old supply lines that show brittleness, cracks, or corrosion.
- Forgetting the gasket or putty, leading to a leak at the sink base.
- Ignoring the sink hole count, which often causes a mismatched purchase.
Recommended Gear
- Basin wrench: Reaches mounting nuts in tight spaces under the sink where a standard wrench cannot fit. View on Amazon
- Plumber’s putty: Seals the faucet base against the sink deck on many models. View on Amazon
- Penetrating lubricant: Loosens corroded nuts and fittings before you apply force. View on Amazon
FAQ
Do I need a plumber to change a kitchen faucet?
Most homeowners with basic hand tools can complete the swap. If shutoff valves are missing, corroded, or leaking, or if the sink has an unusual hole layout, consult a licensed plumber before proceeding.
How long does changing out a kitchen faucet take?
Plan on one to three hours for a typical swap. Older homes with rusted fittings often take longer because stuck nuts require patience and extra lubricant.
Will a new faucet fit my existing sink?
It will if the hole count and mounting style match your sink. Check the number of holes and the spacing before buying, and see Three Hole Faucet Kitchen Guide: Setup, Sizing and Buying Tips for sizing help.
Conclusion
Changing out a kitchen faucet comes down to matching the fit, shutting off the water, and connecting the lines without over-tightening. Work slowly, test every connection, and keep the gasket and putty step in mind. A careful swap can be done in an afternoon.
Related reading
- Kitchen Faucet with Pull-Out Sprayer: How to Choose and Install One (2026)
- Wall Mounted Kitchen Sink Faucet: A Step-by-Step Guide for Beginners
- Wall Hung Kitchen Faucet: A Step-by-Step Guide to Choosing and Installing One
- Two Handle Faucet Kitchen: 7 Best Picks Compared (2026)
Ready to choose one?
