We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Change a Bathroom Sink Faucet: A Step-by-Step Guide (2026)

Learn how to change a bathroom sink faucet in about an hour. Covers shutoff valves, disconnecting supply lines, mounting the new faucet, and leak checks.

Updated November 2026

To change a bathroom sink faucet, you shut off the water, disconnect the old supply lines and mounting hardware, set the new faucet into the sink holes, and reconnect everything with a leak-free seal. Most swaps take one to two hours for someone comfortable with basic hand tools. The steps below cover the process for standard faucets with two supply lines and a mounting nut or locknut under the sink.

Before You Start: Check Your Sink and Faucet Setup

Measure the number of holes in your sink or countertop first. A single-hole faucet, a three-hole widespread setup and a centerset faucet each mount differently, so the replacement has to match. Check the spacing too: many faucets fit a 4-inch center-to-center layout, while others need a 8-inch spread. If you are unsure which type you have, compare the old faucet’s base to the product specifications before you buy. For a closer look at setup types, see Bathroom Sink Faucet Centerset: 5 Best Picks for Every Vanity (2026) and Bathroom Sink Faucet One Hole: 7 Best Picks for Every Vanity (2026).

Shopping for one? See our guide: 6 Best Vintage Brass Bathroom Faucet Picks for Period-Style Sinks (2026).

Step-by-Step: Remove the Old Bathroom Sink Faucet

  1. Turn off the water at the shutoff valves under the sink. If the valves are stiff or do not close fully, shut off the main water supply to the house.
  2. Turn on the faucet to drain remaining water and relieve pressure.
  3. Place a towel or bucket under the supply lines. Use an adjustable wrench to loosen the nuts connecting the supply lines to the faucet shanks, then detach the lines.
  4. Remove the mounting nuts or locknuts holding the faucet to the sink or deck. A basin wrench reaches these in tight spaces.
  5. Lift the old faucet out. Scrape away old plumber’s putty or silicone from the sink surface.

How to Install the New Faucet and Connect the Supply Lines

Set the new faucet’s gasket or rubber seal onto the sink surface, following the manufacturer’s instructions. Insert the faucet through the holes and hand-tighten the mounting hardware from underneath. Keep the faucet centered and aligned before fully tightening, since it is much harder to adjust once the nuts are snug.

Next, connect the supply lines. Most homeowners attach the lines to the faucet shanks first, then to the shutoff valves. Tighten each connection firmly but do not overtighten plastic fittings, which can crack. Some installers wrap threaded connections with plumber’s tape, though many modern faucets seal with rubber washers instead.

Tools and Supplies Checklist

  • Adjustable wrench and basin wrench
  • Bucket and towels
  • Plumber’s putty or silicone sealant (if the manufacturer calls for it)
  • Plumber’s tape (for threaded connections)
  • Flashlight
  • Replacement supply lines if the old ones are cracked or corroded

Test for Leaks and Finish the Job

Open the shutoff valves slowly, one at a time, and watch each connection. Turn on the faucet and let it run for a minute with the drain open, then check the supply line joints and the base of the faucet for drips. Run hot and cold water separately to confirm both sides flow properly. If a connection weeps, tighten it gently a quarter turn at a time. Repairing a dripping cartridge after installation is a separate task; for that, see Bathroom Sink Faucet Drip Repair: 5 Best Kits for Every Fix (2026).

Common Mistakes to Avoid

  • Skipping the water shutoff and getting soaked when disconnecting lines.
  • Buying a faucet that does not match the number of sink holes.
  • Overtightening plastic nuts, which can crack and cause leaks.
  • Forgetting to clean old putty off the sink, which prevents a proper seal.
  • Failing to run water and check for leaks before closing the cabinet.
  • Basin wrench: Reaches mounting nuts in tight spaces under the sink where a regular wrench cannot fit. View on Amazon
  • Braided stainless steel supply lines: Replacing old supply lines during the swap prevents future leaks at the same connections. View on Amazon
  • Plumber’s putty: Creates a watertight base between the faucet and sink when the manufacturer recommends it. View on Amazon

FAQ

How long does it take to change a bathroom sink faucet?

Most people finish in one to two hours. Stubborn, corroded nuts or tight cabinet space can add time.

Do I need to replace the supply lines too?

It is a good idea if the existing lines are old, cracked or corroded. New lines are inexpensive insurance against future leaks.

Can I install a new faucet without a plumber?

Yes, if you are comfortable with basic hand tools and shutting off water. If you find damaged shutoff valves or pipes, consult a licensed plumber before continuing.

Conclusion

Changing a bathroom sink faucet comes down to shutting off water, removing old hardware, mounting the new faucet and testing every connection. Matching the faucet to your sink’s hole setup before you start prevents most problems. Take your time with the leak check, and the job should hold up for years.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Kitchen Bath Channel.