We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Instal a Bathroom Faucet: A Step-by-Step Guide for Beginners

Learn how to instal a bathroom faucet in about two hours with basic tools. Follow these steps for shutoff valves, supply lines, mounting and leak testing.

Updated November 2026

Knowing how to instal a bathroom faucet lets you replace an old or leaking fixture without calling a plumber. Most single-hole and centerset faucets can be installed in an afternoon with basic tools, provided you prepare the sink and shutoff valves properly. This guide walks through the process from start to finish.

Before You Start: Gather Tools and Check Your Sink

Confirm the new faucet matches your sink’s mounting holes. Single-hole sinks accept one-handle faucets, while three-hole sinks take widespread or centerset designs. Check that you have the right supply lines, typically 3/8-inch compression fittings of 12 to 20 inches in length.

Shopping for one? See our guide: 10 Best Wall Mounted Faucet Bathroom Options for Every Need (2026).

  • Adjustable wrench and basin wrench
  • Plumber’s putty or silicone sealant
  • Flathead screwdriver and Phillips screwdriver
  • Bucket and towels
  • Flashlight
  • New supply lines and a pop-up drain assembly if the old one is worn

How to Remove the Old Faucet and Prep the Sink

Turn off the hot and cold shutoff valves under the sink, then open the faucet to drain remaining water. Disconnect the supply lines with an adjustable wrench, placing a bucket underneath to catch drips. Loosen the mounting nuts beneath the sink using a basin wrench, then lift the old faucet out. Scrape away old putty or sealant and wipe the sink surface clean and dry.

How to Install the New Faucet

Set the Faucet and Gasket

Apply plumber’s putty or follow the manufacturer’s instructions for the base gasket. Feed the faucet’s supply lines and any mounting rods or hoses through the sink holes. Press the faucet firmly onto the sink so the gasket seals evenly.

Secure the Mounting Hardware

From underneath, slide the washers and mounting nuts onto the shanks or rods. Tighten them evenly by hand first, then snug them with a basin wrench. Overtightening can crack porcelain or distort the base, so stop once the faucet no longer shifts when you grip it.

Connect the Supply Lines and Drain

Attach the hot line to the left shutoff valve and the cold line to the right, unless the faucet instructions say otherwise. Hand-tighten each compression nut, then give it an extra quarter to half turn with a wrench. Install the pop-up drain assembly according to its kit instructions, and connect the drain tailpiece to the trap.

How to Test and Finish the Installation

Open the shutoff valves slowly to avoid a sudden surge that can loosen fittings. Run the faucet on low for a minute, then check every connection for drips. If you see a leak at a compression nut, tighten it slightly. Then turn the faucet on full and let it run for a few minutes to flush debris from the lines, and wipe away any excess putty.

Common Mistakes to Avoid

  • Skipping the shutoff valve check. Old valves can fail when turned, so test them before you start.
  • Overtightening plastic nuts, which can crack or strip threads.
  • Opening valves too fast, which can blow out a loose connection.
  • Forgetting to flush debris from the new lines before final testing.
  • Reversing hot and cold lines, which is common with unlabeled supply tubes.
  • Basin wrench: Reaches mounting nuts tucked behind the sink where a standard wrench cannot fit. View on Amazon
  • Braided stainless steel supply lines: Resist bursting better than vinyl lines and are simple to attach. View on Amazon
  • Plumber’s putty: Creates a watertight seal under the faucet base and is easy to remove later. View on Amazon

For help choosing a fixture before you begin, see Delta One Hole Bathroom Faucet: How to Choose and Install One (2026) and Bathroom Faucet Three Hole: How to Choose and Install One (2026). If your new faucet is a Moen model, Moen Bathroom Faucet Remove Handle: Step-by-Step Guide (2026) covers the handle removal steps you may need.

FAQ

Do I need to turn off the water supply before installing a bathroom faucet?

Yes. Close both shutoff valves under the sink before disconnecting anything. If the valves do not close fully, shut off the main water supply to the house.

How long does it take to install a bathroom faucet?

Most homeowners finish a standard single-hole installation in one to two hours, not counting time spent on stubborn old nuts or corroded valves.

What if my shutoff valves are old or leaking?

Replace them before installing the new faucet, since a failed valve can flood the cabinet. If you are unsure how to proceed, consult a licensed plumber.

Conclusion

Learning how to instal a bathroom faucet comes down to careful prep, snug (not forced) connections and a thorough leak test. Work slowly, check your fit before tightening, and keep the shutoff valves in mind. With those steps, a standard swap is a manageable weekend project.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Kitchen Bath Channel.