We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Replace Sink Faucet Bathroom: A Step-by-Step Guide (2026)

Learn how to replace sink faucet bathroom fixtures yourself, from shutting off water to connecting supply lines and testing for leaks.

Updated November 2026

To replace a sink faucet in a bathroom, you shut off the water, disconnect the old supply lines and mounting nuts, remove the faucet, set the new one with its gasket, and reconnect everything. Most swaps take one to two hours with basic hand tools, and the result is a faucet that fits your vanity and seals tight. The steps below apply to most single-hole and centerset vanity faucets.

Before You Start: Check Your Faucet and Vanity

Before buying a replacement, confirm the number of holes in your sink or countertop. A single-hole faucet fits one opening, a centerset uses three holes spaced about 4 inches apart, and a widespread model needs three separate holes. Measure the distance between the supply line stubs under the sink as well, since a mismatch means you will need flexible connector lines.

Also note whether the sink has a pop-up drain. You can usually replace the faucet without removing the drain, but a stuck or leaking drain assembly is worth fixing at the same time. If you are comparing options, our guide on 7 Best Replace Bathroom Sink Faucets (2026): Our Picks covers how different designs fit common vanities.

How to Replace a Bathroom Sink and Faucet Step by Step

Step 1: Shut off the water and drain the lines

Close the angle stop valves under the sink by turning them clockwise until they stop. Then open the faucet to release remaining pressure and let any water drain into a bucket.

Step 2: Disconnect the supply lines and mounting hardware

Place a bucket and towels under the sink. Unscrew the supply lines from the shutoff valves, then loosen the mounting nuts that hold the faucet to the sink or countertop. A basin wrench reaches these nuts in tight spaces. Spray penetrating oil on corroded nuts and wait 10 to 15 minutes before trying again.

Step 3: Remove the old faucet

Lift the faucet straight up and out. If it resists, check for remaining hidden nuts or a caulk seal around the base and cut through it with a utility knife. Clean the mounting surface with a plastic scraper so the new gasket seats flat.

Step 4: Install the new faucet

Set the new faucet’s gasket or plate on the sink, then feed the supply lines through the holes. Tighten the mounting nuts from underneath by hand first, then a quarter turn with a wrench. Overtightening can crack ceramic or stress plastic sinks.

Step 5: Reconnect the water and test

Attach the supply lines to the shutoff valves, hand-tightening the connections before a quarter turn with a wrench. Open the valves slowly, then run hot and cold water for about a minute while checking every joint for drips. Wipe the joints dry and check again after 30 minutes.

Tools and Supplies Checklist

  • Adjustable wrench and basin wrench
  • Bucket and old towels
  • Penetrating oil
  • Plastic putty knife or scraper
  • Utility knife for old caulk
  • Replacement supply lines if lengths don’t match
  • Plumber’s putty or silicone sealant, if the manufacturer recommends it

Common Mistakes and Tips

  • Skipping the water shutoff test. Confirm the valves are closed by running the faucet before you disconnect anything.
  • Overtightening the mounting nuts, which can crack the sink or distort the gasket.
  • Forgetting to check the supply line length before buying the new faucet.
  • Reusing old, stiff supply lines. Replacing them costs little and prevents later leaks.
  • Ignoring the manufacturer’s installation sheet, which lists exact torque and sealing steps for that model.

A basin wrench is the single most useful tool for this job because it reaches mounting nuts behind the vanity that a standard wrench cannot. View on Amazon

Braided stainless supply lines are a common upgrade when the old lines are cracked or the lengths are off. View on Amazon

Penetrating oil loosens seized nuts and makes disassembly far less frustrating. View on Amazon

FAQ

Do I need a plumber to replace a bathroom sink faucet?

Most homeowners can handle this swap with basic tools, provided the shutoff valves work and the sink is in good shape. If valves are corroded, leaking or won’t close, a licensed plumber should handle the repair before you proceed.

How long does it take to replace a bathroom faucet?

A straightforward replacement usually takes one to two hours. Corroded nuts or old caulk can add time, so plan for a longer afternoon if the faucet has been installed for many years.

Can I reuse the old supply lines?

You can reuse them if they are flexible, leak-free and the right length. Many people replace them anyway, since new lines are inexpensive insurance against drips.

Conclusion

Replacing a bathroom sink faucet comes down to shutting off the water, removing the old hardware, setting the new faucet with its gasket and testing every connection. Take your time with the nuts and check the joints before you walk away. For related projects, see How to Replace a Kitchen Sink Faucet: A Step-by-Step Guide (2026) or Bathroom Sink Faucet Replacement: A Step-by-Step Guide for 2026.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Kitchen Bath Channel.