How to Fix Leaky Bathroom Faucet: A Step-by-Step Guide for Beginners
Learn how to fix a leaky bathroom faucet in a few steps, from shutting off the water to replacing the cartridge, washers or O-rings. No plumber needed.
Updated November 2026
Most leaky bathroom faucets can be fixed in under an hour with a few basic tools. This guide shows you how to fix a leaky bathroom faucet by identifying where the leak is coming from, shutting off the water, and replacing the worn part that is causing the problem. The steps below cover single-handle and two-handle faucets.
Find Out Where the Leak Is Coming From
Before you take anything apart, figure out which of three areas is leaking. A drip from the spout that continues after the handle is off usually points to a worn cartridge, valve seat or washer. Water leaking from the base of the handle or around the spout collar often means a failed O-ring or packing nut. Water pooling under the sink suggests a loose supply line or a leak in the connection below the faucet. If you are unsure, read our guide on Bathroom Faucet Is Leaking: How to Find and Fix the Drip Yourself to narrow it down.
Shopping for one? See our guide: 4 Best Delta Bathroom Faucet Repair Kit Picks for Every Fix.
Shut Off the Water and Remove the Handle
Close the hot and cold shutoff valves under the sink, then open the faucet to drain the remaining water. Plug the drain so small screws do not disappear down it. Pry off the decorative cap on the handle, remove the screw underneath, and lift the handle off. Single-handle faucets often have a set screw hidden under a cap, usually on the front or side of the handle.
- Turn off both shutoff valves and open the faucet to release pressure.
- Cover the drain with a towel or stopper.
- Pry off the handle cap with a flat-head screwdriver wrapped in tape.
- Remove the handle screw and lift the handle straight up.
- Unscrew the bonnet or packing nut with an adjustable wrench, wrapping the jaws in tape to protect the finish.
Replace the Worn Part
Once the internals are exposed, inspect the part you suspect. On compression faucets, the rubber washer and brass valve seat wear out and cause constant dripping; replace the washer and, if the seat is pitted, the seat as well. Cartridge faucets use a single cartridge that often needs full replacement rather than repair. Ball faucets rely on rubber seals and springs, which should be swapped as a set. Take the old part to a hardware store so you can match the size and brand exactly, since fittings vary between manufacturers.
When reassembling, apply a light coat of plumber’s grease to new O-rings and washers. Do not overtighten the packing nut or bonnet, because this can crack the body or damage new seals. Tighten until snug, then open the shutoff valves slowly and check for leaks.
Repair Kit Versus Individual Parts
If you are unsure which part failed, a repair kit for your faucet brand includes the most common wear items in one package. Our article on Bathroom Faucet Repair Kits: How to Fix a Leaky Faucet in 6 Steps explains how to choose the right kit.
Common Mistakes and Tips
- Forgetting to turn off both hot and cold valves, which leads to unexpected spray.
- Using too much force on corroded nuts. Penetrating oil and a few minutes of patience work better.
- Mixing up hot and cold parts. Many cartridges are keyed, so note their orientation before removal.
- Skipping the drain plug. Small screws and springs are easy to lose.
- Replacing parts without taking a photo of the assembly first.
Recommended Gear
- Adjustable wrench with a wide jaw: Gives you enough grip on packing nuts without slipping and scratching the finish. View on Amazon
- Plumber’s grease: Keeps O-rings supple and helps them seal properly on reassembly. View on Amazon
- Faucet repair kit for your brand: Bundles the common wear parts so you are not guessing sizes. View on Amazon
FAQ
Do I need to turn off the main water supply?
Usually no. The shutoff valves under the sink control water to that faucet only. If those valves are old or do not close fully, you may need to shut off the main supply at the house.
Why does my faucet keep dripping after I replace the washer?
The valve seat may be pitted or worn, which a new washer cannot seal against. Inspect the seat and replace it if needed.
When should I call a plumber?
If the faucet body is cracked, the leak continues after replacing the cartridge or washer, or you find corrosion in the supply lines, a licensed plumber can diagnose the problem safely.
Conclusion
Identifying the leak source, shutting off the water, and replacing the correct worn part will fix most bathroom faucet leaks. Work slowly, keep track of your parts, and test the faucet before closing the cabinet. If the problem persists, a plumber can help identify less obvious causes.
Related reading
- How to Fix a Leaky Bathroom Tub Faucet: A Step-by-Step Guide
- How to Fix Leaky Sink Faucet Bathroom: A Step-by-Step Guide
- How to Repair Leaky Bathroom Faucet: A Step-by-Step Guide for Beginners
Ready to choose one?
