How to Repair a Leaky Bathroom Sink Faucet: A Step-by-Step Guide
Learn how to repair a leaky bathroom sink faucet in a few hours. Find the leak source, shut off water, replace the cartridge or washers, and test your fix.
Updated November 2026
To repair a leaky bathroom sink faucet, you need to identify the type of faucet, shut off the water supply, and replace the worn part causing the drip, usually a cartridge, washer, O-ring or valve seat. Most repairs take one to two hours with basic hand tools. This guide walks through diagnosing the leak, making the repair and checking your work.
Identify the Faucet Type and Leak Source
Start by finding out what kind of faucet you have, because the repair depends on the mechanism inside. Compression faucets use rubber washers and have separate hot and cold handles. Cartridge faucets, common in single-handle models, use a cylinder that controls flow and temperature. Ball faucets use a slotted ball and several springs and seats. Ceramic disc faucets use two stacked discs and rarely need repair beyond cleaning or replacing the cartridge.
Shopping for one? See our guide: Bathroom Leaky Faucet Repair Kits: 7 Best Picks Compared (2026).
Next, locate the leak. A drip from the spout usually points to a worn cartridge, washer or seat. Water leaking around the base of the handle or the body typically means a failed O-ring or packing nut. Tracing the source before you take anything apart saves time and avoids buying the wrong parts. Manufacturers often publish exploded parts diagrams for their faucets, and a quick search by brand and model name will usually turn one up.
Shut Off the Water and Disassemble the Faucet
- Close the hot and cold shutoff valves under the sink. Turn them clockwise until they stop.
- Open the faucet to drain remaining water and relieve pressure.
- Place a towel in the sink basin and cover the drain so small screws or clips don’t fall in.
- Pry off the decorative cap on the handle, then remove the handle screw with a Phillips or hex key.
- Unscrew the packing nut or retaining clip. Lift out the cartridge, stem or ball assembly.
Take photos at each stage. Lining up the old parts with the new ones is easier when you can see how they were seated.
Replace the Worn Components
Compare the removed parts to replacements before buying. For cartridge faucets, the cartridge is usually the only item you need to replace, and the brand and model number stamped on the old one will match a replacement. For compression faucets, replace the washer, O-ring and, if pitted, the valve seat. Use a seat wrench to remove seats, and take the old washer to the store to confirm the size.
Apply a thin coat of plumber’s grease to new O-rings and cartridge seals. This helps them seat without tearing and reduces future friction. Reassemble in reverse order, snugging screws firmly but not forcing plastic parts.
Tools and Supplies Checklist
- Adjustable wrench or basin wrench
- Phillips and flathead screwdrivers
- Hex (Allen) key set
- Seat wrench (for compression faucets)
- Replacement cartridge, washers or O-rings
- Plumber’s grease
- Old towel and small container for screws
Test the Repair and Check for Leaks
Slowly open the shutoff valves, then turn on the faucet and run it on both hot and cold. Check the spout, the base of the handle and the supply connections under the sink. Let the faucet run for a minute, then shut it off and watch for drips over the next several minutes. If the spout still drips, the seat may be scored and need replacing. If water seeps around the handle, tighten the packing nut slightly or check the O-ring position.
Common Mistakes and Tips
- Skipping the shutoff valves. Even closed valves can leak, so drain the line before disassembly.
- Buying parts without matching the brand and model. Many faucets use proprietary cartridges.
- Overtightening. This cracks plastic parts and damages seats.
- Forgetting the drain cover. Small parts disappear quickly down a sink.
- Ignoring the supply lines. If the leak is at the connection under the sink, tighten or replace the supply line.
Recommended Gear
- Plumber’s grease helps O-rings and cartridge seals slide into place and resist wear. View on Amazon
- Basin wrench reaches the nuts behind the sink where a standard wrench won’t fit. View on Amazon
- Faucet cartridge puller removes stuck cartridges without damaging the body. View on Amazon
FAQ
Do I need to replace the whole faucet to fix a leak?
Usually not. Most leaks come from a worn cartridge, washer, O-ring or seat, all of which are inexpensive and replaceable. Replace the whole faucet only if the body is cracked or the parts are no longer available.
How do I know which cartridge to buy?
Check the brand name and model number stamped on the old cartridge or listed in the manufacturer’s parts diagram. Bring the old part to a hardware store if you are unsure.
Can a dripping faucet waste much water?
A steady drip can waste a substantial amount of water over a month, so repairing it promptly is worthwhile. If you have health or safety concerns about water quality, consult a licensed plumber.
Conclusion
Repairing a leaky bathroom sink faucet comes down to identifying the faucet type, shutting off the water and replacing the worn part. With the right replacement and careful reassembly, most leaks stop in an afternoon. If the problem persists or involves the supply lines, a licensed plumber can finish the job safely.
Related reading
- How to Repair Leaky Bathroom Faucet: A Step-by-Step Guide for Beginners
- Bathroom Faucet Repair Kits: How to Fix a Leaky Faucet in 6 Steps
- How to Fix Leaky Sink Faucet Bathroom: A Step-by-Step Guide
Ready to choose one?
