We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Repair Dripping Bathroom Sink Faucet: A Step-by-Step Guide

Learn how to repair a dripping bathroom sink faucet in a few hours with basic tools. Find the drip source, identify your faucet type, and stop the leak for good

Updated November 2026

To repair a dripping bathroom sink faucet, you shut off the water, figure out whether your faucet uses a cartridge, ball, disc, or compression valve, and replace the worn part that lets water pass. Most drips come from a worn washer, O-ring, cartridge, or valve seat, and a typical repair takes one to two hours with basic hand tools. The steps below cover the process from start to finish.

Identify the Source of the Drip

Before you take anything apart, confirm where the water is coming from. A faucet can drip from the spout, which usually points to the internal valve, or from the base around the handle, which usually points to a worn O-ring or packing nut. Turn the handle fully off and watch the spout for a minute. If water keeps falling, the valve is not sealing.

Shopping for one? See our guide: Bathroom Sink Faucet Drip Repair: 5 Best Kits for Every Fix (2026).

Next, check the faucet type. Single-handle faucets usually use a cartridge or ball assembly. Two-handle faucets usually use compression valves with rubber washers, or ceramic disc cartridges. Knowing the type tells you which replacement part you need. If you are unsure, start with the replacement guide that matches your model.

Gather Tools and Replacement Parts

Having everything ready before you start prevents a half-disassembled faucet from sitting for days. Most repairs need only common household tools.

  • Adjustable wrench or basin wrench
  • Flathead and Phillips screwdrivers
  • Allen (hex) key set, often needed for set screws under handle caps
  • Plumber’s grease and a rag
  • Replacement cartridge, washers, O-rings, or valve seat matched to your faucet brand
  • A small bowl to hold screws and small parts

Manufacturers often publish parts diagrams for their faucets. If you can find the brand and model number, you can order the exact cartridge rather than guessing. For a deeper look at reading those diagrams, see Moen Bathroom Faucet Parts Diagram: How to Read It and Order the Right Part if your faucet is a Moen.

Shut Off the Water and Disassemble the Faucet

Close the hot and cold angle stop valves under the sink. If they are stiff or do not close fully, shut off the main supply to the house. Open the faucet to drain remaining water. Put a towel in the sink basin so a dropped screw does not disappear down the drain.

  1. Pry off the decorative cap on the handle and remove the handle screw.
  2. Lift off the handle. On some models, a set screw under the handle requires a hex key.
  3. Unscrew the bonnet nut or retaining nut using an adjustable wrench, turning counterclockwise.
  4. Remove the cartridge, stem, or compression valve. Note how it sits, and take a photo before removing it.
  5. Inspect the valve seat at the bottom of the faucet body for pitting, debris, or mineral buildup.

Replace the Worn Part and Reassemble

Install the new cartridge or washer exactly as the old one came out. Orientation matters. Many cartridges have a tab or index pin that must line up with the faucet body. Apply a thin layer of plumber’s grease to new O-rings before seating them. Grease helps them seal and reduces friction on the next turn.

If the valve seat is scored, a seat wrench can resurface it, but many repairs call for replacing the seat entirely. Reassemble in reverse order, tightening the retaining nut snugly without overtightening, which can crack plastic components. Reattach the handle, cap, and screw. Then open the angle stop valves slowly and check for leaks while running the faucet on hot and cold.

Common Mistakes

  • Reassembling without matching the old part. Brand-specific cartridges look similar but are not interchangeable.
  • Forgetting to shut off the water fully before disassembly, which leads to a sudden spray.
  • Overtightening the retaining nut, which can crack the body or damage the seat.
  • Skipping plumber’s grease on O-rings, which can cause them to tear during reinstallation.
  • Ignoring a worn valve seat. A new cartridge will drip again if the seat underneath is damaged.

A basin wrench reaches the mounting nuts under the sink, where an adjustable wrench often cannot. A hex key set covers the set screws found on many modern handles. Plumber’s grease keeps new O-rings supple and prevents tearing during installation.

FAQ

Can I repair the faucet without replacing the whole unit?

Yes. In most cases you only need to replace the cartridge, washers, O-rings, or valve seat. A full replacement is usually necessary only when the faucet body is cracked or corroded beyond repair.

Why does my faucet keep dripping after I replaced the cartridge?

The valve seat underneath may be scored or clogged with mineral deposits, or the cartridge may not be fully seated. Remove the cartridge again, clean the seat, and confirm the cartridge’s index tab lines up with the faucet body.

How long does a bathroom faucet repair usually take?

Most homeowners finish a single-handle cartridge replacement in one to two hours. Compression faucets with corroded parts can take longer, especially if the retaining nuts are stuck.

Conclusion

A dripping bathroom sink faucet is usually a worn cartridge, washer, O-ring, or valve seat, and replacing that part stops the leak. Shut off the water, identify your faucet type, and match the new part to the original brand. If the faucet body itself is damaged, it may be time to replace the entire unit, and a licensed plumber can help if the supply lines or shutoff valves need attention.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Kitchen Bath Channel.