We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Change a Kitchen Faucet: A Step-by-Step Guide for Beginners

Learn how to change a kitchen faucet in one afternoon with basic tools. Covers shutoff valves, removal, hookup, leak testing and common mistakes to avoid.

Updated November 2026

To change a kitchen faucet, you shut off the water, disconnect the old supply lines, remove the mounting hardware, and install the new faucet with its own hoses and mounting nut. Most homeowners can finish a standard single-hole swap in two to three hours with basic hand tools. The steps below cover what to check before you buy, how to do the swap, and how to test for leaks afterward.

Check Your Sink and Faucet Before You Start

Start by measuring the number of holes in your sink deck. A single-hole faucet uses one opening, a three-hole setup uses a spout and two handles spaced about 4 inches apart, and a widespread faucet uses separate holes for each handle. A new faucet with a different hole pattern may need a deck plate or a new sink, so confirm the match first.

Shopping for one? See our guide: Delta Tap Kitchen Faucet Review: Key Features Explained.

Look under the sink as well. Note whether you have compression or braided supply lines, and check the diameter of the threads on the shutoff valves. Most US kitchen faucets use 3/8-inch compression fittings, but confirm before you order.

Tools and Materials You Will Need

  • Adjustable wrench and basin wrench
  • Bucket and old towels
  • Flashlight or headlamp
  • Plumber’s putty or silicone sealant, depending on the faucet’s instructions
  • Replacement supply lines, if the old ones are corroded or too short
  • The new faucet, with its mounting hardware and gasket

Step-by-Step: Removing the Old Faucet

  1. Shut off the water. Turn the under-sink shutoff valves clockwise until they stop. If they seize or leak, shut off the main supply to the house.
  2. Open the faucet. Run the hot and cold taps to drain remaining water and relieve pressure.
  3. Disconnect the supply lines. Place a bucket below the connections. Loosen the nuts with the adjustable wrench and unscrew the lines from the shutoff valves.
  4. Remove the mounting nut. Reach under the sink with the basin wrench and turn the large nut counterclockwise. Some faucets have a plastic nut that can be loosened by hand.
  5. Lift the faucet out. Pull it up from the top. Scrape off old putty or sealant from the sink deck with a plastic scraper so the new gasket seats flat.

Installing the New Kitchen Faucet

Set the new gasket or plumber’s putty on the sink deck as the manufacturer directs. Insert the faucet through the hole or holes and seat it level. Working from below, slide the washers and mounting nut onto the shank and tighten by hand first. Then use the basin wrench to snug it, keeping the faucet centered and aligned with the sink back.

Connect the supply lines next. Thread the hoses to the faucet shank, then attach the other end to the shutoff valves. Hand-tighten each connection, then add a quarter turn with a wrench. Over-tightening can crack plastic nuts or damage compression seats.

Testing for Leaks and Finishing Up

Turn the shutoff valves back on slowly. Run both hot and cold water for about a minute, then check every connection with a dry paper towel. Any dampness means the connection needs a small additional turn or a new washer. Operate the handle through its full range and check for spray or drips at the base. Wipe the faucet, then clean up any sealant residue before it hardens.

Common Mistakes

  • Skipping the water shutoff test. Confirm the valves close fully before you disconnect anything.
  • Reusing old, brittle supply lines. Replacing them costs little compared with a leak behind the cabinet.
  • Tightening the mounting nut crooked, which can make the handle sit at an angle.
  • Forgetting to flush the new lines before the aerator is installed, which can clog it with debris.
  • Basin wrench: Reaches the mounting nut in the tight space behind the sink, where a standard wrench can’t fit. View on Amazon
  • Braided stainless supply lines: Resist bursting better than rubber hoses and are a common upgrade during a faucet swap. View on Amazon
  • Plumber’s putty: Seals the base of the faucet against the sink deck, and is easy to remove later if you need to service the faucet. View on Amazon

FAQ

Can I change a kitchen faucet without a plumber?

Yes, most homeowners can handle a standard swap with basic tools. If the shutoff valves are corroded or the sink needs modification, consult a licensed plumber.

How long does it take to change a kitchen faucet?

A simple single-hole replacement usually takes two to three hours. Older homes with seized valves or stubborn nuts can take longer.

Do I need to replace the supply lines when I change the faucet?

Not always, but it is a good idea if the existing lines are old, stiff, or cracked. Replacing them while the cabinet is open is much easier than doing it later.

Conclusion

Changing a kitchen faucet comes down to shutting off the water, removing the old unit, and seating the new one carefully. Measure your sink holes first, and test every connection before you walk away. For related help, see Moen Kitchen Faucet Install: A Step-by-Step Guide for Beginners or Replace Kitchen Faucet Aerator: 6 Best Picks for Easy Swaps (2026).

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Kitchen Bath Channel.