We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Fix a Kitchen Faucet: A Step-by-Step Guide for Common Leaks

Learn how to fix a kitchen faucet that drips, sprays weakly or sticks. Follow these steps to find the cause, replace the right part and stop the leak.

Updated November 2026

Most kitchen faucet problems come down to a handful of worn parts: a cartridge, a washer, an O-ring, or a clogged aerator. To fix a kitchen faucet, you need to identify the symptom, shut off the water, replace the failing part and test the result. Most repairs take under an hour and need only basic hand tools.

Identify the Problem Before You Take Anything Apart

The symptom usually points to the part. A faucet that drips from the spout when it is off typically has a worn cartridge or valve seat. Dripping or leaking at the base of the handle often means a failed O-ring or packing nut. Low flow or a spray that sputters usually means a clogged aerator or spray head. Water leaking from the connection under the sink points to a supply line or fitting.

Shopping for one? See our guide: 6 Best Kitchen Sink Faucet Repair Kits for Every Fix (2026).

Turn the handle slowly through its full range while watching the spout and base. Note exactly where the water appears, because that tells you which section to open.

Shut Off the Water and Remove the Handle

Close the under-sink shutoff valves for the hot and cold lines. If the valves are stiff or do not close fully, shut off the main supply to the house. Open the faucet to drain remaining water and relieve pressure.

  1. Pry off the decorative cap on top of the handle with a flathead screwdriver or a thin putty knife.
  2. Remove the handle screw with the correct Phillips or Allen wrench and lift the handle off.
  3. Unscrew the retaining nut or clip that holds the cartridge or stem in place.
  4. Pull out the cartridge or stem. Take a photo before removing anything else so you can reassemble it correctly.

Replace the Failing Part

For a cartridge-style faucet, the cartridge is usually the fix. Pull the old one straight out, note the orientation of the tabs or notches, and insert the new cartridge the same way. Many manufacturers specify that the cartridge must sit flat and seat fully before you reinstall the retaining clip.

For a compression faucet, replace the washer and O-ring, and inspect the valve seat for pitting. Lightly grease new O-rings with silicone plumber’s grease. For a ball-type faucet, replace the springs, seals and ball if the seals are worn.

If the spout drips even after a new cartridge, check the spout connection and make sure the cartridge is seated correctly. A debris-filled supply line can also damage new seals, so run the water briefly with the aerator removed before reassembling.

For a weak or uneven spray, unscrew the aerator at the spout tip and clean it under running water. Soak it in white vinegar if mineral buildup remains. Replace it if the screen is torn or the threads are damaged.

Reassemble, Test and Check for Leaks

Reinstall the parts in reverse order. Hand-tighten the retaining nut first, then snug it with a wrench without overtightening, since overtightening can crack plastic components. Turn the water supply back on slowly and open the faucet to purge air from the lines. Run hot and cold water through the full range, then check the base, spout and supply connections for drips after ten minutes.

Tools and Supplies You Will Likely Need

  • Adjustable wrench and basin wrench
  • Phillips and flathead screwdrivers, plus the correct Allen wrench for your faucet
  • Replacement cartridge, washers, O-rings or aerator matched to your brand and model
  • Silicone plumber’s grease and a soft rag
  • Bucket or towel to catch residual water

Common Mistakes to Avoid

  • Skipping the shutoff valves and starting work with water still under pressure.
  • Buying a part without the faucet brand and model number, which often leads to the wrong fit.
  • Forgetting the cartridge orientation, which can cause the handle to run backward or leak.
  • Overtightening plastic nuts and cracking the body of the faucet.
  • Ignoring a cracked or pitted valve seat, which will keep leaking after a new cartridge.

A basin wrench lets you reach and tighten nuts behind the sink, where a standard wrench cannot fit. View on Amazon

Silicone plumber’s grease keeps O-rings supple and prevents them from tearing during reinstallation. View on Amazon

A small set of Allen wrenches and a magnetic tray help you keep small handle screws and clips from getting lost. View on Amazon

FAQ

Do I need to replace the whole faucet to stop a drip?

No. Most drips come from a worn cartridge, washer or O-ring, and replacing that single part is far cheaper and faster than swapping the faucet. A full replacement is only worth considering if the body itself is cracked or the brand no longer supplies parts. For guidance on matching parts, see Pfister Kitchen Faucet Parts: Identify, Order and Replace the Right Ones.

Why is my faucet still dripping after I replaced the cartridge?

The new cartridge may not be seated fully, or the valve seat underneath may be damaged or full of mineral debris. Remove the cartridge again, clean the seat, and confirm the cartridge is oriented correctly before reinstalling. If the problem continues, the seat itself may need replacement.

How do I know which replacement part to buy?

Look for the brand name and model number, usually stamped on the faucet body or listed in the manufacturer’s manual. Bring the old part to the store if possible, or compare dimensions and tab patterns before ordering. If you are unsure, consult a licensed plumber before purchasing.

Conclusion

Learning to fix a kitchen faucet usually means finding the source of the leak or weak flow, then replacing one worn part. Shut off the water, take photos as you disassemble, and install the new part carefully without overtightening. With those steps, most common repairs can be completed in a single afternoon.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Kitchen Bath Channel.