We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Change a Faucet Bathroom: A Step-by-Step Guide for Beginners

Learn how to change a faucet bathroom in a few hours with basic tools. Covers shutoff valves, removal, mounting and leak checks for beginners.

Updated November 2026

To change a faucet in a bathroom, you shut off the water, disconnect the old faucet’s supply lines, remove its mounting hardware, and install the new unit with its own gaskets and connectors. Most single-hole or centerset swaps take one to three hours for a first-timer. The steps below cover what to check before you buy, how to remove the old faucet, and how to confirm the new one doesn’t leak.

Before You Start: Check Your Sink and Supply Lines

Look under the sink first. Count the mounting holes on the sink deck, since single-hole, three-hole and centerset layouts need different faucets. Note the supply line type too: flexible braided lines are the most common, while older homes may have rigid copper or chrome-plated pipe.

Shopping for one? See our guide: Change Moen Bathroom Faucet Cartridge: 5 Best Replacements (2026).

Measure the distance between the sink’s mounting holes if you have a centerset sink, and confirm your new faucet’s spread matches. For a broader look at layouts, see Bathroom Faucet Three Hole: How to Choose and Install One (2026) and Delta One Hole Bathroom Faucet: How to Choose and Install One (2026).

How to Remove the Old Bathroom Faucet

  1. Shut off the water. Turn the angle stops under the sink clockwise until they stop. If they’re stiff or don’t close, shut off the main water supply to the house.
  2. Turn on the faucet to relieve pressure and drain remaining water into a towel-lined bucket.
  3. Disconnect the supply lines using an adjustable wrench or basin wrench. Hold the stop valve steady so it doesn’t twist.
  4. Remove the mounting nuts or the locking nut under the sink. A basin wrench reaches the tight spots near the back of the sink.
  5. Lift the old faucet out from above. Clean any old plumber’s putty or silicone from the sink deck with a plastic scraper.

Installing the New Faucet

Set the new faucet’s gasket or rubber seal on the sink deck before you drop the faucet into the holes. Thread the mounting hardware from below and tighten evenly, snugging the nuts by hand first. Overtightening can crack a porcelain or stone sink, so hand-tight plus a quarter turn with a wrench is usually enough.

Connect the supply lines to the new faucet’s tails, then attach them to the angle stops. Keep the lines relaxed, without kinks or sharp bends.

Checklist: Tools and Supplies

  • Adjustable wrench and basin wrench
  • Bucket and towels
  • Plastic putty knife or scraper
  • Plumber’s tape or the connectors included with the faucet
  • Flashlight

Testing for Leaks and Final Adjustments

Turn the water back on slowly at the angle stops. Open the faucet and let it run for a minute to flush debris from the lines. Then check each connection with a dry paper towel. Tighten any nut that shows moisture, but stop as soon as the drip stops.

Run hot and cold water and check the flow and temperature. If a drip persists after installation, the cartridge or seals may be faulty. Guides like Repair Dripping Faucet Bathroom: A Step-by-Step Guide for Beginners and Bathroom Faucet Repair Kits: How to Fix a Leaky Faucet in 6 Steps cover that next step.

Common Mistakes to Avoid

  • Skipping the shutoff check. Always confirm the water is off before disconnecting anything.
  • Using too much force on the mounting nuts, which can crack the sink.
  • Forgetting the deck gasket, which leads to leaks at the sink surface.
  • Buying a faucet with the wrong hole count or spread for your sink.
  • Cross-threading the supply connections. Start each nut by hand.
  • Basin wrench: Reaches the mounting nuts at the back of the sink, where a standard wrench won’t fit. View on Amazon
  • Plumber’s putty: Seals the base of the faucet against the sink deck, especially on sinks without a rubber gasket. View on Amazon
  • Flexible supply lines: Connect the faucet to the shutoff valves when the included lines are too short or worn. View on Amazon

FAQ

Do I need a plumber to change a bathroom faucet?

Most homeowners can handle a standard single-hole or centerset swap with basic tools. If the shutoff valves are corroded, leaking or won’t close, a licensed plumber is the safer choice.

How long does it take to change a bathroom faucet?

A first-timer typically needs one to three hours, depending on how stubborn the old nuts are and whether the supply lines need replacing.

What if my shutoff valves won’t turn?

Don’t force them, since that can break the valve. Shut off the main house supply instead, and consider having the valves replaced by a plumber.

Conclusion

Changing a bathroom faucet comes down to shutting off the water, removing the old hardware carefully, and installing the new unit with the right seals. Check your sink’s hole count and spread before buying, and test every connection before you walk away. With a little patience, most people can finish the job in an afternoon.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Kitchen Bath Channel.