We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Change Out a Bathroom Sink Faucet: A Step-by-Step Guide

Learn how to change out a bathroom sink faucet in about an hour. Covers shutoff valves, supply lines, mounting nuts, tools, and common mistakes to avoid.

Updated November 2026

To change out a bathroom sink faucet, you shut off the water, disconnect the old supply lines and mounting hardware, lift the old unit out, and install the new faucet following its included instructions. Most homeowners can finish the job in about one to two hours with basic hand tools. The process is the same for most single-hole, centerset, and widespread faucets, with a few differences in how the faucet is secured.

Before You Start: Gather Tools and Check Your Setup

Before you touch anything, confirm what you’re working with. Look under the sink and note whether the supply lines come straight from the wall or from shutoff valves, and whether the faucet has one, two, or three holes in the sink deck. Your new faucet needs to match that hole count, or you’ll need a deck plate or cover.

Shopping for one? See our guide: 6 Best Vintage Brass Bathroom Faucet Picks for Period-Style Sinks (2026).

Step-by-Step: Removing the Old Faucet

  1. Turn off both hot and cold shutoff valves under the sink. If the valves are stiff or don’t close fully, shut off the main water supply to the house.
  2. Open the faucet to drain remaining water and relieve pressure.
  3. Place a bucket or towel under the supply connections and use an adjustable wrench or basin wrench to disconnect the supply lines.
  4. Remove the mounting nuts beneath the sink. A basin wrench reaches these in tight spaces.
  5. Lift the old faucet out from above. Clean any old putty or sealant from the sink surface.

Installing the New Bathroom Faucet

Most new faucets arrive with a gasket or plate that goes between the faucet base and the sink. Set that gasket in place, feed the faucet’s supply lines and mounting studs through the holes, and tighten the mounting nuts from below by hand first. Then snug them with a wrench, taking care not to overtighten, which can crack a porcelain or ceramic sink.

Next, connect the supply lines to the shutoff valves. Hand-tighten first, then give each connection a quarter to half turn with a wrench. If your faucet uses a pop-up drain assembly, install it according to the manufacturer’s diagram before reconnecting the drain.

Testing for Leaks and Final Adjustments

Slowly reopen the shutoff valves, then turn on the faucet and check every connection for drips. Run hot and cold water for a minute each and watch for water at the base of the faucet and under the sink. Tighten any connection that weeps, but avoid cranking down hard on plastic or compression fittings. Finally, wipe the faucet and sink dry so you can spot any new moisture later.

Common Mistakes to Avoid

  • Skipping the shutoff valve test. If a valve won’t close, fix it or shut off the main before you begin.
  • Overtightening mounting nuts, which can crack the sink.
  • Buying a faucet with the wrong hole count for your sink.
  • Forgetting to flush the new supply lines before final tightening, which can leave debris in the aerator.
  • Reusing old, hardened washers or gaskets instead of the ones supplied with the new faucet.
  • Basin wrench: Reaches mounting nuts in tight spaces under the sink, where a standard wrench won’t fit. View on Amazon
  • Adjustable wrench: Handles supply line connections and general tightening without marring finishes. View on Amazon
  • Plumber’s putty: Seals the base of the faucet or drain assembly against the sink surface when your model calls for it. View on Amazon

FAQ

Do I need a plumber to change a bathroom sink faucet?

Many homeowners handle this job themselves with basic tools. If your shutoff valves are corroded or your supply lines are inaccessible, a licensed plumber can help you avoid water damage.

How long does it take to replace a bathroom faucet?

Most people finish in about one to two hours, though older or stuck hardware can extend the job. Plan extra time if you’re working in a tight vanity.

Why is my new faucet dripping after installation?

A loose supply line connection or a missing gasket is the usual cause. Tighten the connections gently and confirm the gasket sits flat between the faucet and sink.

Conclusion

Changing a bathroom sink faucet comes down to shutting off the water, removing the old hardware carefully, and installing the new unit with the right gaskets and firm, measured tightening. Check for leaks before you call the job done. Take your time with the mounting nuts, and you’ll have a fresh-looking sink in an afternoon.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Kitchen Bath Channel.