We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Change Out a Kitchen Sink Faucet: A Step-by-Step Guide

Learn how to change out a kitchen sink faucet in a few hours with basic tools. Covers shutoff valves, supply lines, mounting and leak testing.

Updated November 2026

To change out a kitchen sink faucet, you shut off the water, disconnect the old supply lines and mounting hardware, set the new faucet, and reconnect everything with a leak-free seal. Most homeowners can finish the job in two to four hours with basic hand tools. The steps below cover prep, removal, installation and testing.

Before You Start: Prep and Measurements

Start by checking how many holes your sink has. Standard kitchen sinks come as single-hole, three-hole (faucet, plus separate sprayer and soap dispenser) or four-hole designs. A faucet with a spray head or soap dispenser needs matching holes, or a deck plate to cover unused ones. Check the new faucet’s spec sheet for hole size and mounting style before buying. Our guide on Kitchen Faucet Four Hole: How to Choose and Install One (2026) explains the hole-count question in more detail.

Shopping for one? See our guide: 6 Best Kitchen Sink Faucet Moen Models for Every Need (2026).

Look under the sink as well. You need working shutoff valves on both the hot and cold lines. If the valves are stiff, crusted or leak when turned, replace them before the faucet swap, or you will be dealing with a second leak later.

Removing the Old Faucet

  1. Turn off both shutoff valves and open the faucet to drain residual water.
  2. Place a towel or bucket under the valves and disconnect the supply lines with an adjustable wrench, holding the valve steady so it doesn’t twist.
  3. If the faucet has a sprayer hose, disconnect it from the base and note how it routes.
  4. Loosen the mounting nuts on the underside of the sink. Many faucets use a plastic or metal nut and a rod. A basin wrench reaches these tight spaces far better than a standard wrench.
  5. Lift the old faucet out. Scrape off old putty or gasket material from the sink surface so the new base sits flat.

Installing the New Faucet

Most manufacturers specify whether to use a gasket, plumber’s putty or both. Follow their instructions, because the wrong sealant can prevent a tight fit. Feed the faucet’s supply lines and sprayer hose through the holes, set the base in place, and tighten the mounting nuts from underneath until the faucet is snug but not cracked down. Over-tightening can crack porcelain or stress plastic parts.

Connecting the Supply Lines

Attach the hot line to the hot valve and the cold line to the cold valve. Hand-tighten the nuts first to avoid cross-threading, then give them a quarter to half turn with a wrench. Wrap the threads with plumber’s tape if the connection is metal-to-metal and the instructions call for it. Hot and cold lines are often color-coded, but double-check the labels on the faucet body.

Testing for Leaks

Open both shutoff valves slowly. Run the faucet at low pressure, then check each connection under the sink for drips. Let the water run hot and cold for a minute, switch the sprayer on and off, and look again. Dry the connections with a paper towel and watch for moisture over the next hour. If you find a drip, tighten the nut slightly, or shut off the water and reseat the gasket. Persistent leaks often trace back to a misaligned supply line or a worn cartridge.

Common Mistakes

  • Skipping the shutoff valve check and finding a stuck valve after the new faucet is in.
  • Over-tightening mounting nuts, which can crack the sink or distort the faucet base.
  • Forgetting to clean old putty, leaving the new base uneven and prone to leaks.
  • Cross-threading supply line nuts by starting them at an angle.
  • Testing only once. Check for leaks again after a few hours of normal use.
  • Basin wrench: Reaches mounting nuts in tight spaces under the sink, where a regular wrench won’t fit. View on Amazon
  • Plumber’s putty: Seals the faucet base to the sink surface when the manufacturer calls for it. View on Amazon
  • PTFE thread seal tape: Helps seal threaded supply line connections without over-tightening. View on Amazon

FAQ

Do I need a plumber to change a kitchen faucet?

Many homeowners handle it themselves, since the job involves basic tools and simple connections. If the shutoff valves are damaged or the sink has unusual mounting, a licensed plumber is the safer choice. Consult a professional if you’re unsure about any step.

How long does it take to replace a kitchen sink faucet?

Most first-time installs take two to four hours, including prep and testing. Plan extra time if the old faucet is seized or the shutoff valves need replacing.

Can I reuse the old supply lines?

You can reuse them if they are in good condition, but replacing them is inexpensive insurance against leaks. Look for cracks, bulging or corrosion at the connections, and swap them out if you see any.

Conclusion

Changing a kitchen sink faucet comes down to careful prep, clean removal, a secure mount and a thorough leak test. Confirm your sink’s hole count before you buy, and take your time with the connections. For more options, see How to Replace a Kitchen Sink Faucet: A Step-by-Step Guide (2026).

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Kitchen Bath Channel.