How to Disconnect Moen Kitchen Faucet: A Step-by-Step Guide for Beginners
Learn how to disconnect a Moen kitchen faucet safely, from shutting off water to loosening supply lines and removing the mounting nut. Follow these steps.
Updated November 2026
To disconnect a Moen kitchen faucet, you shut off the water supply, relieve the pressure, detach the supply lines and hoses, and loosen the mounting nut underneath the sink. Once those connections are free, the faucet lifts off the countertop. The whole job usually takes under an hour, and it is the first step before any repair, replacement or upgrade.
Before You Start: Shut Off the Water
Most under-sink setups have two shutoff valves, one for hot water and one for cold, usually on the supply lines. Turn them clockwise until they stop. If the valves are stiff or do not close fully, shut off the main water supply to the house instead. Then open the faucet to drain remaining water and relieve pressure. Keep a towel and a bucket under the sink, since a small amount of water will still come out.
Shopping for one? See our guide: 6 Best Kitchen Sink Faucet Moen Models for Every Need (2026).
How to Disconnect the Supply Lines and Hoses
With the water off, you can work on the connections beneath the sink. Most Moen faucets use flexible supply lines that thread onto the shutoff valves, plus a spray hose on models with a pull-out or side sprayer.
- Place a bucket under the shutoff valves and have a towel ready.
- Loosen each supply line nut by hand first. Use an adjustable wrench only if the nut does not turn freely, and hold the valve steady so you do not twist the shutoff itself.
- Unscrew the spray hose from the base of the faucet body. On pull-out models, gently guide the hose up through the faucet and detach it from the weight or docking clip.
- Disconnect any side sprayer or soap dispenser tubing if your model has them. Note the routing so reinstalling is easier.
Remove the Mounting Nut and Lift the Faucet
The faucet is held to the sink or countertop by a mounting nut on a threaded shank, often with a plastic or metal mounting plate above it. Working from below, reach up and loosen the nut counterclockwise. Many Moen installations use a plastic retaining nut that can be turned by hand, so avoid forcing it. Once the nut is off, lift the faucet straight up and out. If it is stuck from old caulk or mineral buildup, run a utility knife gently around the base first.
Tools You Will Likely Need
- Bucket and towels
- Adjustable wrench or basin wrench
- Flashlight for working under the sink
- Plumber’s grease or silicone-safe lubricant for stubborn threads
- Utility knife for cutting old caulk
Common Mistakes to Avoid
- Skipping the shutoff step. Even a closed valve can leak if it is worn, so always open the faucet after closing the valves to check.
- Over-tightening or forcing the supply nuts, which can crack plastic fittings or damage the valve seat.
- Losing track of small parts such as clips, washers and the mounting plate. Lay them out in order on a towel.
- Pulling the faucet up without checking for a remaining connection, such as a soap dispenser line or sprayer weight.
- Working on a dirty or wet sink base, which makes it hard to see the nut and fittings.
Recommended Gear
A basin wrench reaches the mounting nut in tight spaces where a standard wrench cannot fit, so it is the most useful tool for this job. View on Amazon
A headlamp keeps both hands free while you loosen nuts in the dark cabinet behind the sink. View on Amazon
FAQ
Do I need to turn off the main water to disconnect a Moen kitchen faucet?
Not always. If the individual shutoff valves under the sink close fully and hold, you can work from there. If they are stiff, leak or do not close, shut off the main supply to the house.
Can I disconnect the faucet without removing the sink?
Yes. The faucet is mounted to the sink deck and connected from underneath, so you only need access to the area below the sink, not to remove the sink itself.
What if the mounting nut will not budge?
Apply penetrating lubricant and wait a few minutes, then try again with a basin wrench. Avoid excessive force, since it can crack the sink or the nut. If it still will not move, a licensed plumber can help.
Conclusion
Shut off the water, detach the supply lines and spray hose, then loosen the mounting nut and lift the faucet out. Taking your time with each connection prevents leaks and broken fittings. If you are repairing the faucet next, see our guide on How to Repair a Moen Kitchen Faucet: A Step-by-Step Guide for Beginners.
Related reading
- Moen Faucet Drips Kitchen: How to Find and Stop the Leak (Step-by-Step)
- Kitchen Faucet Moen Cartridge: How to Identify, Remove and Replace It
- Replacement Cartridge for Moen Kitchen Faucet: A Step-by-Step Guide (2026)
- Moen vs Kohler Kitchen Faucet: 3 Best Picks Compared (2026)
Ready to choose one?
