We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Repair a Kitchen Faucet: A Step-by-Step Guide for Beginners

Learn how to repair a kitchen faucet at home. Follow these steps to diagnose leaks, drips and low flow, then replace the right part without calling a plumber.

Updated November 2026

Learning how to repair a kitchen faucet usually comes down to three things: shutting off the water, identifying the faulty part, and replacing it. Most drips, leaks and weak sprays come from worn washers, O-rings, cartridges or aerators, and each of these can be swapped with basic hand tools in under an hour. This guide walks through the process for common single-handle faucets.

Gather Tools and Shut Off the Water

Before you touch the faucet, turn off the water supply. Look for two small valves under the sink and turn them clockwise until they stop. If the valves are stiff or do not shut off fully, close the main water supply to the house and open the faucet to drain remaining pressure.

Shopping for one? See our guide: 5 Best Kitchen Faucet Parts Price Pfister Options for Easy Repairs (2026).

Keep these tools nearby:

  • Adjustable wrench and basin wrench
  • Phillips and flathead screwdrivers
  • Allen wrench set (many faucet handles use a hex screw)
  • Plumber’s grease and white vinegar
  • A soft cloth and a small towel to protect the sink finish
  • Replacement parts matched to your faucet brand and model

Diagnose the Problem Before You Disassemble

Identifying the source saves time. Run the faucet and note where the problem appears:

  • Dripping from the spout: usually a worn cartridge, ball or washer.
  • Leaking around the handle base: typically a worn O-ring or cartridge seal.
  • Weak or uneven flow: often a clogged aerator or mineral buildup in the cartridge.
  • Leaking from the sprayer hose: a damaged hose or loose connection under the sink.

If your faucet is a specific brand, you can find model-specific guidance. For example, readers with Moen fixtures can check How to Repair a Moen Kitchen Faucet: A Step-by-Step Guide for Beginners, and those with a dripping spout may find Moen Faucet Drips Kitchen: How to Find and Stop the Leak (Step-by-Step) especially useful.

Replace the Cartridge, Washer or O-Rings

Most repairs follow the same general sequence:

  1. Remove the decorative cap and loosen the handle screw. Lift the handle off.
  2. Unscrew the bonnet nut or retaining clip with a wrench. Wrap the wrench in tape to avoid scratching the finish.
  3. Pull out the cartridge or stem. Note its orientation, since reinstalling it backward is a common mistake.
  4. Compare the old part to the new one. Match size, height and connector style.
  5. Coat new O-rings with plumber’s grease, then install the new cartridge or washer and reassemble in reverse order.

Clean the Aerator and Spray Head

Unscrew the aerator at the spout tip and soak it in white vinegar for about 30 minutes. Rinse it under running water and reinstall. If the sprayer produces weak flow, check the head for debris and clear the holes with a pin. For sprayer-specific issues, see How to Repair Kitchen Faucet Sprayer: A Step-by-Step Guide.

Test the Repair and Check for Leaks

Turn the water supply back on slowly. Run the faucet at low and high settings, then check the base, spout and connections for moisture. Let the faucet run for several minutes and dry the area with a towel to confirm there is no slow seep. Tighten any fittings a quarter turn at a time if you spot water, but avoid overtightening, which can crack plastic parts.

  • Plumber’s grease keeps O-rings supple and helps them seal without tearing. View on Amazon
  • A basin wrench reaches the mounting nuts behind the sink where a standard wrench cannot. View on Amazon
  • A faucet cartridge puller helps remove stuck stems without damaging the body. View on Amazon

Common Mistakes to Avoid

  • Skipping the water shutoff, which leads to spraying water across the cabinet.
  • Forgetting the orientation of the cartridge or stem before removing it.
  • Using the wrong replacement part, since many faucets look similar but use different sizes.
  • Scratching the finish with metal tools. Use tape or a cloth on the wrench jaws.
  • Overtightening plastic nuts, which can crack and cause new leaks.

FAQ

Can I repair a kitchen faucet myself?

Yes, most single-handle repairs need only basic hand tools and a replacement cartridge, washer or O-ring. If you find corroded pipes, water damage or a leak inside the wall, contact a licensed plumber.

How long does a kitchen faucet repair take?

A simple cartridge or aerator fix usually takes 20 to 60 minutes for a first-timer. Locating the correct part can add time, so have your faucet model number ready.

Why does my faucet still drip after replacing the washer?

The valve seat may be worn or corroded, or the new part may not match. Check that the cartridge is seated correctly and inspect the seat for mineral buildup before buying another part.

Conclusion

Repairing a kitchen faucet is manageable with the right tools, a clear diagnosis and a correctly matched replacement part. Shut off the water, take your time with reassembly, and test thoroughly before calling the job finished. For complex issues, a licensed plumber can confirm the fix.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Kitchen Bath Channel.