We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Repair a Leaking Bathroom Sink Faucet: A Step-by-Step Guide

Learn how to repair a leaking bathroom sink faucet in a few steps. Find the drip source, shut off the water, and replace the worn part yourself.

Updated November 2026

To repair a leaking bathroom sink faucet, you shut off the water, identify whether the leak comes from a cartridge, washer, or O-ring, and replace the worn part. Most single-handle and two-handle faucets can be fixed in under an hour with basic hand tools. This guide walks through the process so you can stop the drip and save water.

Find Out What Type of Faucet You Have

Before you buy any parts, confirm the faucet style, because the repair depends on the internal mechanism. Two-handle faucets usually use a compression stem with rubber washers, while single-handle faucets typically use a cartridge, ball, or ceramic disk. Look at the handle: a single lever that moves side to side points to a cartridge or ball design, and separate hot and cold handles usually point to a stem or cartridge system.

Shopping for one? See our guide: Bathroom Leaking Faucet Repair: 6 Best Repair Kits Compared (2026).

Remove the handle cap and check for a brand name or model number stamped on the faucet body. Manufacturers often publish exploded parts diagrams that show exactly which components you need.

Shut Off the Water and Remove the Handle

Close the shutoff valves under the sink, then open the faucet to drain remaining water. Put a towel in the basin to protect the finish and to catch small parts that might fall.

  1. Pry off the decorative cap on top of the handle with a flat blade wrapped in tape.
  2. Remove the handle screw, usually hidden under the cap, with a Phillips or hex key.
  3. Lift the handle off. If it is stuck, gently wiggle it rather than forcing it.
  4. Unscrew the retaining nut or cartridge clip that holds the internal part in place.

Replace the Worn Part

Pull out the cartridge, stem, or washer assembly. Take it to a hardware store or use the brand’s parts diagram to match the exact replacement. Using a generic part of the wrong size is one of the most common reasons a repair fails.

  • Cartridge faucets: Replace the entire cartridge. These are sold as a single unit and are difficult to repair piece by piece.
  • Compression faucets: Replace the rubber washer and the seat washer. Check the brass seat for pitting, and replace it if it is rough.
  • Ball faucets: Replace the O-rings and rubber seats around the ball, and inspect the springs.

Coat new O-rings with plumber’s silicone grease, which keeps them from tearing during reassembly. Do not use petroleum-based lubricants, since they can degrade rubber.

Reassemble, Test, and Check for Leaks

Reverse the disassembly steps and tighten all fittings snugly without overtightening, since excess force can crack plastic parts. Reattach the handle, turn the shutoff valves back on slowly, and run the faucet at low pressure. Check under the sink for drips around connections and check the spout for a steady flow when the handle is off. If the leak continues, the new part may be the wrong size or seated improperly, and you should recheck the installation.

  • Adjustable wrench set helps you loosen stubborn nuts without marring the finish. View on Amazon
  • Plumber’s silicone grease keeps O-rings sealed and moving smoothly during reassembly. View on Amazon
  • Faucet repair kit with assorted washers and O-rings gives you spare parts if the first one does not match. View on Amazon

Common Mistakes

  • Skipping the water shutoff, which leads to a wet, messy repair.
  • Buying a part without checking the brand and model number first.
  • Overtightening the retaining nut, which can crack the body or damage threads.
  • Forgetting to plug the drain, so small parts disappear.
  • Replacing only the washer when the seat or cartridge is the real source of the leak.

For more detailed walkthroughs, see How to Repair a Bathroom Faucet Leak: A Step-by-Step Guide for Beginners and How to Fix a Bathroom Sink Faucet Leak: A Step-by-Step Guide. If you find the leak is coming from the supply lines or the valve body, a licensed plumber can diagnose the problem safely.

FAQ

Why does my bathroom faucet keep dripping after I replace the washer?

The valve seat is often the real problem, since a worn or pitted seat will keep leaking even with a new washer. Inspect the seat and replace it if it looks rough or corroded.

Do I need to turn off the main water supply?

Usually no, because the shutoff valves under the sink isolate the faucet. If those valves are stuck or leak, you may need to close the main supply instead.

When should I call a plumber instead?

Call a professional if the leak comes from inside the wall, the supply lines are corroded, or the faucet body itself is cracked. Water damage behind walls can be costly, so a licensed plumber is worth the call.

Conclusion

Repairing a leaking bathroom sink faucet comes down to shutting off the water, identifying the faulty part, and replacing it with a matched component. With patience and a parts diagram, most drips can be stopped in an afternoon. Keep spare washers or a repair kit on hand for future fixes.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Kitchen Bath Channel.