We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Stop a Dripping Bathroom Faucet: A Step-by-Step Guide

Learn how to stop a dripping bathroom faucet in a few steps. Find the cause, shut off the water, and replace the worn part so the drip stops for good.

Updated November 2026

To stop a dripping bathroom faucet, you need to shut off the water, identify the type of faucet you have, and replace the worn part that lets water pass through. Most drips come from a worn washer, cartridge, valve seat, or O-ring, and the repair usually takes under an hour with basic hand tools. This guide walks through the process so you can fix the leak without calling a plumber.

Find the Source of the Drip

Before you take anything apart, confirm that the faucet itself is leaking and not the supply line or drain. Dry the faucet, wait a few minutes, and watch where the water comes from. A drip from the spout points to a worn internal part, while water pooling at the base usually means a seal or O-ring has failed.

Shopping for one? See our guide: 10 Best Wall Mounted Faucet Bathroom Options for Every Need (2026). How to Repair a Dripping Moen Faucet: 6 Steps to Stop the Leak goes further into this.

Next, identify the faucet type. Compression faucets have separate hot and cold handles and use rubber washers. Cartridge faucets, including most single-handle models, use a plastic or brass cartridge. Ball faucets use a slotted ball and several rubber seals. Ceramic disc faucets use two ceramic plates. Knowing the type tells you which part to replace. If you are unsure, the Types of Bathroom Faucet: 5 Main Styles and How to Choose One (2026) article explains each style in detail.

Shut Off the Water and Disassemble the Faucet

Turn off the water supply under the sink by closing both hot and cold shutoff valves. Then open the faucet to drain the remaining water. Plug the drain with a rag so small parts do not fall in.

  1. Pry off the decorative cap on the handle and remove the handle screw.
  2. Lift the handle off and unscrew the bonnet or retaining nut with an adjustable wrench, wrapping the nut in tape to protect the finish.
  3. Remove the stem, cartridge, or valve assembly. Note the orientation of each part, and take a photo before you remove anything.
  4. Inspect the washer, O-rings, cartridge, and valve seat for cracks, grit, or mineral buildup.

If the faucet is a model you are not familiar with, a parts diagram from the manufacturer can help you match the replacement. The Moen Bathroom Faucet Parts Diagram: How to Read It and Order the Right Part article shows how to read one.

Replace the Worn Parts

Replace the part you found damaged, and always use a kit or part made for your faucet brand and model. A universal washer may fit loosely and drip again within weeks. Lightly grease new O-rings with silicone plumbers’ grease before installing them. Reassemble in reverse order, tighten the retaining nut snugly without overtightening, and reattach the handle.

If the valve seat is pitted or scored, a seat wrench can resurface or replace it. For cartridge faucets, a new cartridge is usually a simpler fix than trying to clean the old one. The How to Repair a Bathroom Faucet Leak: A Step-by-Step Guide for Beginners article covers several of these repairs in more depth.

Turn the Water Back On and Test

Open the shutoff valves slowly, then run the faucet on hot and cold for about 30 seconds to clear air and debris. Close the handle fully and check the spout for at least five minutes. If it still drips, the seat or cartridge may need closer inspection, or the seal may not be fully seated.

  • Silicone plumbers’ grease: Keeps O-rings flexible and reduces wear during reassembly. View on Amazon
  • Adjustable wrench set: Lets you loosen retaining nuts without scratching the finish. View on Amazon
  • Faucet repair kit for your brand: Bundles the washers, O-rings, and springs that usually wear out first. View on Amazon

Common Mistakes

  • Skipping the shutoff valves and getting soaked by water still in the line.
  • Overtightening the retaining nut, which can crack the bonnet or damage the seat.
  • Buying a universal part without matching the brand and model.
  • Forgetting to plug the drain, which can swallow small washers or screws.
  • Replacing the washer when the valve seat is the real problem, so the drip returns.

FAQ

Why does my bathroom faucet keep dripping after I replace the washer?

The valve seat is often worn or pitted, so a new washer cannot seal against it. Inspect the seat and resurface or replace it if it is damaged.

Can I fix a dripping faucet without turning off the main water?

Usually you can close the local shutoff valves under the sink, which isolates that faucet. If the valves are stuck or leak, consider shutting off the main supply and consulting a licensed plumber.

When should I call a professional?

Call a licensed plumber if the valves will not shut off, the supply pipes are corroded, or you cannot identify the faucet type. Water damage behind walls can be costly, so professional help is worth it in those cases.

Conclusion

A dripping bathroom faucet is usually caused by a worn washer, cartridge, or valve seat, and each can be replaced with basic tools. Shut off the water, identify the faucet type, and match the replacement part to your brand and model. Test the faucet carefully, and the drip should stop for good.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Kitchen Bath Channel.