How to Take Kitchen Faucet Off: A Step-by-Step Guide for Beginners
Learn how to take kitchen faucet off safely, from shutting off water to disconnecting supply lines and lifting the fixture off the sink deck.
Updated November 2026
Learning how to take kitchen faucet off is a manageable job for most homeowners with basic tools and a couple of hours. You will shut off the water, disconnect the supply lines, release the mounting hardware and lift the old faucet clear of the sink. Taking it off cleanly also makes it easier to install a replacement or inspect the valve underneath.
Before You Start: Shut Off the Water
Locate the shutoff valves under the sink, usually one for hot and one for cold. Turn them clockwise until they stop. If the valves are stiff or do not close fully, shut off the main water supply to the house instead. Then open the faucet to relieve pressure and let any remaining water drain into a bucket.
Shopping for one? See our guide: Delta Tap Kitchen Faucet Review: Key Features Explained.
Disconnect the Supply Lines and Spray Hose
Place a towel and a shallow bucket beneath the connections, since a small amount of water will still come out. Use an adjustable wrench or basin wrench to loosen the compression nuts on the hot and cold supply lines. Hold the valve body steady with a second wrench so you do not twist the stub-outs. If your faucet has a pull-down spray, unthread the hose from the base and pull it through the deck.
Remove the Mounting Hardware
Most kitchen faucets are secured by a mounting nut or a pair of nuts on threaded studs beneath the sink. Access these from below with a basin wrench, since the space is tight. Some models use a plastic mounting plate or a locking nut that must be backed off gradually. Once the nuts are loose, lift the faucet straight up and out of the holes in the sink deck.
Watch for Stuck Sealant and Gaskets
Old putty or silicone can bond the base to the sink. Slide a plastic putty knife around the base rather than prying with metal, which can scratch stainless or porcelain. Remove any old gasket or rubber seal from the deck so the new faucet sits flat.
Checklist: Tools and Supplies
- Adjustable wrench and basin wrench
- Bucket and towels
- Flashlight or headlamp for working underneath
- Plastic putty knife
- Penetrating lubricant for seized nuts
- Painter’s tape to protect the sink finish
Common Mistakes to Avoid
- Skipping the shutoff check. Confirm water has stopped by opening the faucet before loosening anything.
- Forcing corroded nuts without lubricant, which can crack the supply lines or the valve body.
- Using metal tools on the sink surface, which leaves scratches that show under sink lighting.
- Losing track of small parts. Sort the nuts, washers and gaskets in a labeled cup.
- Forgetting the spray hose, which can snag or drop into the cabinet if left attached.
Recommended Gear
A basin wrench is the single most useful tool for reaching mounting nuts in a cramped cabinet. A headlamp keeps both hands free while you work overhead. A penetrating lubricant helps when old nuts have corroded in place.
- Basin wrench for reaching mounting nuts beneath the sink. View on Amazon
- Headlamp for hands-free lighting in the cabinet. View on Amazon
- Penetrating lubricant for loosening seized nuts. View on Amazon
FAQ
Do I need to turn off the main water supply?
Usually no, if the under-sink shutoff valves work properly. If they are stiff, leaking or missing, shut off the main supply to the house before you start.
What if the faucet will not lift out of the sink?
Check for remaining mounting nuts, dried sealant or a spray hose still attached. Loosen the base gently with a putty knife, and never pry hard against the sink surface.
Should I hire a plumber to remove the faucet?
Many homeowners handle this themselves, but if you find badly corroded valves, leaks in the supply lines or damaged cabinetry, consult a licensed plumber before proceeding.
Conclusion
Once the water is off and the supply lines are disconnected, removing a kitchen faucet mostly comes down to patience with the mounting nuts. Work slowly, keep the sink surface protected and sort your hardware as you go. You will then be ready to clean the deck or install a new fixture.
Related reading
- Moen Faucet Drips Kitchen: How to Find and Stop the Leak (Step-by-Step)
- Kitchen Faucet with Pullout Spray: How to Choose the Right One (2026)
- Kitchen Faucet with Pull-Out Sprayer: How to Choose and Install One (2026)
- Kitchen Faucet Moen Cartridge: How to Identify, Remove and Replace It
- Kitchen Faucet Four Hole: How to Choose and Install One (2026)
- How to Replace a Kitchen Sink Faucet: A Step-by-Step Guide (2026)
Ready to choose one?
