Kitchen Faucet Replacement How To: Step-by-Step Guide (2026)
Learn kitchen faucet replacement how to swap an old faucet in a few hours. Covers shutoff valves, disconnecting lines, mounting holes, and common mistakes.
Updated November 2026
Kitchen faucet replacement is a manageable weekend project for most homeowners with basic tools. This guide walks you through shutting off the water, removing the old faucet, checking your sink’s mounting setup, and installing and testing the new one. Most swaps take between one and three hours, depending on how stubborn the old connections are.
Before You Start: Check Fit and Gather Tools
Look under the sink first. Count the mounting holes in your sink or countertop, since single-hole, three-hole and four-hole faucets each need a matching setup. A four-hole faucet with a separate sprayer will not sit flat on a single-hole sink, and many buyers learn this only after the box is open. If you are unsure, read the Kitchen Faucet Four Hole: How to Choose and Install One (2026) guide before buying.
Shopping for one? See our guide: Kitchen Faucet Replacement Parts Price Pfister: 6 Best Picks for Easy Repairs.
Gather these tools:
- Adjustable wrench and basin wrench
- Bucket and old towels
- Plumber’s putty or the gasket supplied with the new faucet
- Flashlight and a helper for lifting the faucet
- Teflon tape and a few new supply lines, if the old ones are cracked
Step-by-Step Faucet Removal
- Shut off the water. Turn the angle stops under the sink clockwise until they stop. If they are seized or do not turn, shut off the main water supply to the house.
- Open the faucet. Run both hot and cold taps to relieve pressure and drain remaining water into the bucket.
- Disconnect the supply lines. Place the bucket beneath the connections. Unscrew the supply lines from the shutoff valves, then from the faucet tails.
- Remove the sprayer hose and mounting nut. Disconnect the spray hose from the base, then loosen the mounting nut with a basin wrench. Reaching the nut is the hardest part, so take your time.
- Lift out the old faucet. Clean any old putty or gasket residue from the sink surface so the new unit seats evenly.
Installing the New Faucet
Dry-fit the new faucet before tightening anything. Set the base over the holes, check that the spout clears the backsplash, and confirm the handles have room to swing. Then follow the manufacturer’s instructions for the specific model, since mounting hardware varies.
- Apply plumber’s putty or seat the gasket between the faucet base and sink surface.
- Feed the supply lines and sprayer hose through the holes, then fasten the mounting nut or plate from below. Tighten snugly. Overtightening can crack porcelain or stress the base.
- Connect the supply lines to the faucet tails, then to the shutoff valves. Hand-tighten first, then add a quarter turn with a wrench.
- Reconnect the sprayer hose to the base and attach any weight or counterweight the design requires.
- Turn the shutoff valves back on slowly and check for leaks.
- Run the faucet on hot and cold for two minutes, then test the sprayer and the diverter.
Checking Your Work and Common Mistakes
Once water is flowing, dry every connection with a paper towel and watch for drips for at least 15 minutes. A connection that looks dry at first can weep once pressure builds. If you need to troubleshoot a leak after installation, the guide on Moen Faucet Drips Kitchen: How to Find and Stop the Leak (Step-by-Step) covers the most common causes.
- Skipping the water shutoff test. Always confirm the valves are closed before disconnecting.
- Overtightening plastic nuts, which can crack and cause slow leaks.
- Reusing old supply lines that show corrosion or bulging.
- Forgetting to flush the new faucet for a minute to clear debris from the lines.
- Buying the wrong hole configuration for your sink.
Recommended Gear
A basin wrench makes reaching the mounting nut far easier than a standard wrench, especially in a tight cabinet. View on Amazon
Braided stainless steel supply lines are a common upgrade during a faucet swap because they resist the cracking that affects older rubber lines. View on Amazon
Plumber’s putty seals the base of the faucet against the sink surface and is easy to clean up if you need to remove the faucet again later. View on Amazon
FAQ
Can I replace a kitchen faucet without a plumber?
Yes, most homeowners can handle a straightforward swap with basic hand tools. If your shutoff valves are seized, your supply lines are hard-wired into the wall, or you are changing the hole configuration, consult a licensed plumber.
How long does a kitchen faucet replacement take?
A simple, same-configuration swap usually takes one to three hours. Older homes with corroded connections or a new sink layout can take longer.
Do I need to replace the supply lines when I replace the faucet?
It is a good idea if the existing lines are old, cracked, or bulging. Replacing them while the sink is already open is inexpensive insurance against future leaks.
Conclusion
Kitchen faucet replacement comes down to three things: shutting off the water completely, matching the new faucet to your sink’s hole count, and tightening connections just enough to seal them. Work slowly, check for leaks at each stage, and let the manufacturer’s instructions guide any model-specific steps.
Related reading
- Replacement Cartridge for Moen Kitchen Faucet: A Step-by-Step Guide (2026)
- Moen Kitchen Faucet Valve Replacement: 4 Best Parts Compared (2026)
- Kohler Kitchen Faucet Cartridge: Step-by-Step Replacement Guide (2026)
- Kohler Kitchen Faucet Cartridge Replacement: 4 Best Picks Compared (2026)
Ready to choose one?
