Repair a Bathroom Faucet: A Step-by-Step Guide for Beginners
Learn how to repair a bathroom faucet yourself. Identify the faucet type, shut off water, replace worn parts, and stop drips in a few hours.
Updated November 2026
To repair a bathroom faucet, you shut off the water, identify the faucet type, remove the handle, and replace the worn part causing the leak or drip. Most repairs take one to two hours and need only basic hand tools. The steps below cover the common faucet styles and show you how to avoid the mistakes that cause repeat leaks.
Identify Your Faucet Type First
Repair steps depend on the internal mechanism, so start by identifying which type you have. Look at the handle and the body of the faucet, then match what you see to one of these common designs:
Shopping for one? See our guide: 4 Best Delta Bathroom Faucet Repair Kit Picks for Every Fix.
- Compression faucets use two separate handles and rubber washers that press against a valve seat. They often drip from the spout when closed.
- Cartridge faucets use a single handle or two handles that control a sealed cartridge. Leaks usually come from the cartridge itself or its O-rings.
- Ball faucets use a single handle on a rotating ball with several rubber seals and springs.
- Ceramic disc faucets use two ceramic disks that slide over each other. They rarely drip, but grit can scratch the disks.
If you are unsure, remove the handle cap and check the markings on the stem or cartridge. Manufacturers often print the model number there, which helps when ordering replacement parts.
Shut Off the Water and Remove the Handle
Close the shutoff valves under the sink. If the valves are stiff or do not close fully, shut off the main water supply to the house instead. Open the faucet to drain the remaining water.
- Place a towel in the sink basin to protect the finish and keep small parts from falling down the drain.
- Pry off the decorative cap on the handle with a flat blade, wrapping the tip in tape to avoid scratches.
- Remove the handle screw with the correct screwdriver or Allen key, then lift the handle off.
- Unscrew the packing nut or retaining nut that holds the stem or cartridge in place.
Replace the Worn Part
Once the internal parts are exposed, the fix depends on what is failing. Take the old part with you when buying a replacement, or match it by the faucet model.
Compression Faucets
Replace the rubber washer and the O-ring on the stem. If the valve seat inside the faucet body is pitted, use a seat wrench to resurface or replace it. Compression faucet leaks are most often caused by worn washers.
Cartridge and Ball Faucets
Pull the cartridge straight out and install a matching replacement, aligning the tabs with the slots in the body. For ball faucets, replace the springs, seats, and O-rings as a set. Lubricate new O-rings with plumber’s grease before installing them.
Ceramic Disc Faucets
Replace the entire cartridge if the disks are cracked or scratched. Ceramic disks are difficult to repair individually, and a new cartridge is usually the reliable fix.
Reassemble and Test the Faucet
Reverse the disassembly steps, tightening screws firmly but not forcing them. Turn the water supply back on slowly, then open and close the faucet several times. Check under the sink for leaks at the connections, and run the faucet for a minute to confirm the drip has stopped.
Common Mistakes to Avoid
- Skipping the shutoff step, which lets water spray during disassembly.
- Using the wrong replacement cartridge or washer size, which causes new leaks.
- Overtightening the handle screw, which can crack the handle or strip threads.
- Forgetting to lubricate O-rings, which leads to tearing and early failure.
- Ignoring corroded valve seats, which will keep dripping even after new washers are installed.
Recommended Gear
- Plumber’s grease keeps O-rings supple and prevents them from tearing during reassembly. View on Amazon
- Seat wrench set lets you remove and resurface valve seats in compression faucets without damaging them. View on Amazon
- Adjustable basin wrench reaches the mounting nuts under the sink that are otherwise hard to access. View on Amazon
FAQ
How long does a bathroom faucet repair usually take?
Most repairs take between one and two hours, including shutting off the water and testing the result. Stiff nuts or corroded parts can add time.
Do I need to replace the whole faucet if it leaks?
Usually not. Most leaks come from a worn washer, O-ring, or cartridge, which are inexpensive and easy to swap. Replace the whole faucet only if the body is cracked or the model is no longer supported.
Why does my faucet still drip after I replaced the washer?
The valve seat is often the cause. If it is pitted or worn, resurface it with a seat wrench or replace it, since a new washer alone will not seal against a rough surface.
Conclusion
Repairing a bathroom faucet comes down to identifying the type, shutting off the water, and replacing the worn washer, O-ring, or cartridge. With careful reassembly and a slow test, most leaks stop on the first try. For complex plumbing problems or damaged supply lines, consult a licensed plumber.
Related reading
- Repair Dripping Faucet Bathroom: A Step-by-Step Guide for Beginners
- How to Repair a Bathroom Faucet Leak: A Step-by-Step Guide for Beginners
- How to Repair Leaky Bathroom Faucet: A Step-by-Step Guide for Beginners
- Bathroom Tub Faucet Parts: Identify, Repair and Replace Each One
- Bathroom Sink Faucet Drip Repair: 5 Best Kits for Every Fix (2026)
Ready to choose one?
