Repair Kitchen Faucet Drip: 5 Steps to Stop the Leak for Good
Learn how to repair a kitchen faucet drip in five steps. Shut off the water, find the cause, replace the worn part, and stop the leak for good.
Updated November 2026
To repair a kitchen faucet drip, you shut off the water, take the faucet apart far enough to reach the cartridge, valve seat or washer, and replace the worn part. Most drips come from a worn rubber seal or a failing cartridge, and a basic repair usually takes under an hour with a few common tools. This guide walks through the process so you can finish the job without calling a plumber.
Find the Source of the Drip
Before you take anything apart, confirm where the water is coming from. A drip from the spout tip usually points to a worn cartridge, valve seat or O-ring. Water leaking from the base of the handle or the spout collar suggests a different seal. Dry the faucet, run it briefly, and watch which part gets wet first. If you want a fuller walkthrough of how to trace a leak, see Moen Faucet Drips Kitchen: How to Find and Stop the Leak (Step-by-Step).
Shopping for one? See our guide: 5 Best Kitchen Faucet Parts Price Pfister Options for Easy Repairs (2026).
Shut Off the Water and Prepare Your Workspace
Turn off the shutoff valves under the sink, then open the faucet to release any remaining pressure. Place a towel in the sink basin so small parts cannot wash down the drain if they slip. Cover the drain opening as well.
- Close the hot and cold shutoff valves under the sink.
- Open the faucet handle to drain the lines.
- Line the sink with a towel and gather a flathead screwdriver, Allen wrenches, an adjustable wrench, plumber’s grease and replacement parts.
Disassemble and Replace the Worn Component
Most single-handle kitchen faucets use a cartridge, while many older two-handle models use compression washers. Remove the handle screw first, lift off the handle and unscrew the cap or retaining nut. Pull out the cartridge or stem and inspect it for grit, cracks, or flattened rubber seals.
Replacing a Cartridge or Seals
Match the new part to your faucet brand and model before buying. Coat new O-rings with plumber’s grease, seat the cartridge in the same orientation as the old one, and reassemble in reverse order. For brand-specific guidance, read How to Repair a Moen Kitchen Faucet: A Step-by-Step Guide for Beginners or Replace Kohler Kitchen Faucet Cartridge: Step-by-Step Guide (2026).
Reassemble, Test and Check for Leaks
Slowly reopen the shutoff valves and check for leaks under the sink before reinstalling the cap. Run the faucet at low and high flow, then turn it off and watch the spout for thirty seconds. If the drip continues, the seat may be scored or the cartridge may be the wrong size.
| Symptom | Likely cause | Fix |
|---|---|---|
| Drip from spout tip | Worn cartridge or valve seat | Replace cartridge or seat |
| Leak at handle base | Worn O-ring | Replace O-rings |
| Drip only when off | Debris in cartridge | Clean or replace cartridge |
Common Mistakes and Tips
- Skipping the shutoff valves and getting soaked when the handle comes off.
- Buying a part without the faucet brand and model number.
- Overtightening plastic nuts, which can crack the body.
- Forgetting to lubricate new O-rings, which can tear them during installation.
- Replacing a cartridge when only the aerator is clogged. Check the aerator first.
Recommended gear
- Plumber’s silicone grease keeps O-rings supple and helps seals slide into place. View on Amazon
- Adjustable wrench with rubber grip protects chrome finishes while you loosen retaining nuts. View on Amazon
- Faucet cartridge puller helps remove a stuck cartridge without damaging the valve body. View on Amazon
FAQ
Why does my kitchen faucet keep dripping after I replace the washer?
The valve seat may be scored or worn, so new rubber cannot seal properly. Inspect the seat and replace it if it has pits or grooves.
Can I repair a drip without shutting off the main water supply?
Yes, in most homes you only need the shutoff valves under the sink. If those valves do not close fully, consult a licensed plumber before continuing.
How do I know which replacement part to buy?
Check the faucet brand, model and the markings on the old cartridge. Taking the old part to a hardware store helps you match it correctly.
Conclusion
A kitchen faucet drip is usually a worn seal or cartridge, and most homeowners can fix it in an hour with basic tools. Shut off the water, identify the leaking part, replace it and test carefully. If the leak persists or the valves will not close, consult a licensed plumber.
Related reading
- Pfister Kitchen Faucet Repair: 5 Steps to Stop Leaks and Drips
- Top 7 Kitchen Water Faucet Repair Kits Compared for Common Leaks
- Repair Kitchen Faucet with Sprayer: 6 Best Repair Kits Compared (2026)
Ready to choose one?
