We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Repair a Leaking Kitchen Faucet: 5 Steps to Stop Drips for Good

Learn how to repair a leaking kitchen faucet in five steps. Find the leak source, replace the worn part, and stop drips without calling a plumber.

Updated November 2026

To repair a leaking kitchen faucet, you need to find out where the water is escaping, shut off the supply, and replace the worn part that is causing the problem. Most leaks come from a worn cartridge, a failed O-ring or a damaged valve seat, and each of these is a repair most homeowners can handle with basic hand tools. The steps below show how to diagnose the leak and make the fix.

Identify Where the Leak Is Coming From

Before you take anything apart, figure out which kind of leak you have. A drip from the spout that continues when the handle is off usually points to the cartridge or valve seat. Water leaking from the base of the faucet, around the handle or at the connection to the sink usually means a failed O-ring or a loose mounting nut. Water pooling under the sink suggests a supply line or a compression fitting.

Shopping for one? See our guide: 5 Best Kitchen Faucet Parts Price Pfister Options for Easy Repairs (2026).

Run the faucet and watch closely. If the leak only appears when the handle is in the on position, the problem is inside the valve body. If it appears when the faucet is off, check the seals around the base.

Shut Off the Water and Prepare Your Tools

Close both angle stop valves under the sink, then open the faucet to drain remaining water from the lines. Place a towel in the basin to protect the finish and keep small parts from going down the drain.

  • Adjustable wrench and basin wrench
  • Phillips and flathead screwdrivers
  • Allen (hex) key set, usually sized 3/32 to 5/32 inch
  • Replacement cartridge, O-rings or valve seat, matched to your faucet brand and model
  • Plumber’s grease and a flashlight

Replace the Worn Cartridge, O-Rings or Valve Seat

Once the water is off, remove the handle, usually by loosening a set screw under a decorative cap. Pull the cartridge or stem straight up, then inspect it for cracks, mineral buildup or torn rubber. Compare it to the replacement part before you buy, since a mismatch is the most common reason a repair fails.

Replacing a Cartridge

Remove the retaining clip or nut that holds the cartridge in place, lift it out and seat the new cartridge with its orientation matching the old one. Apply a thin film of plumber’s grease to the O-rings before reinstalling.

Replacing O-Rings and Valve Seats

Small O-rings around the spout base or stem can be swapped with a pick tool. A valve seat, which sits at the bottom of the valve body, usually needs a seat wrench to remove. Clean the seat area thoroughly, since grit left behind will cause the new part to leak.

Reassemble, Test and Check for Leaks

Reverse the disassembly steps, tightening nuts and set screws snugly but not with excessive force. Slowly open the angle stop valves, then check every connection for drips. Turn the faucet on and off several times, watching the spout and base.

  1. Tighten all fittings and reinstall the handle cap.
  2. Open the water supply slowly to avoid pressure surges.
  3. Run hot and cold water for about 30 seconds each.
  4. Wipe dry and recheck for leaks after 15 minutes.

Common Mistakes to Avoid

  • Buying a part without confirming the brand and model, which often leads to a return trip.
  • Forgetting to shut off both supply valves before disassembly.
  • Overtightening nuts, which can crack plastic components or warp the valve body.
  • Skipping the cleaning step, leaving mineral deposits that cause the new seal to fail.
  • Reusing old O-rings that have hardened or flattened.
  • A basin wrench makes it much easier to reach mounting nuts in tight spaces under the sink. View on Amazon
  • Silicone plumber’s grease keeps O-rings flexible and helps them seal properly on reassembly. View on Amazon
  • A seat wrench is the right tool for removing a valve seat without damaging the valve body. View on Amazon

If you want model-specific instructions, see How to Fix Leaking Moen Kitchen Faucet: A Step-by-Step Guide or Price Pfister Kitchen Faucet Repair: A Step-by-Step Guide (2026). For a faucet that drips from the sprayer, How to Repair Kitchen Faucet Sprayer: A Step-by-Step Guide covers that specific fix.

FAQ

Why does my kitchen faucet keep dripping after I replace the cartridge?

The most common reason is debris or mineral buildup on the valve seat or in the valve body. Clean those surfaces thoroughly and confirm the new cartridge is oriented correctly.

Can I repair a leaking kitchen faucet without turning off the main water supply?

Yes, in most homes you only need to close the angle stop valves under the sink. If those valves are old or do not seal, shut off the main supply to be safe.

When should I call a plumber instead of making the repair myself?

Call a plumber if the leak comes from inside a wall, if the supply lines are corroded or if you cannot identify the faucet’s brand and parts. A professional can also help if the faucet is damaged beyond a simple part swap. Consult a licensed plumber for any gas or electrical concerns near the work area.

Conclusion

A leaking kitchen faucet is usually a worn cartridge, O-ring or valve seat, and replacing that part is a manageable weekend task. Shut off the water, identify the leak source, make the swap carefully and test your work. With the right replacement part and a little patience, the drip should stop for good.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Kitchen Bath Channel.