Replacing Kohler Kitchen Faucet: A Step-by-Step Guide for Beginners
Learn how replacing a Kohler kitchen faucet works, from shutting off water to connecting supply lines and testing for leaks, with tips to avoid common mistakes.
Updated November 2026
Replacing a Kohler kitchen faucet is a manageable weekend project if you work methodically. You will shut off the water, disconnect the old unit, mount the new faucet, connect the supply lines and check for leaks. Most of the work happens under the sink, so plan on a few tight, awkward minutes with a flashlight.
Before You Start: Confirm Fit and Gather Tools
Check the number of holes in your sink or countertop before you buy a replacement. Kohler faucets are typically sold as single-hole, centerset (three-hole with a 4-inch spread) or widespread (three-hole with an 8-inch spread) configurations. A single-hole faucet can be installed on a three-hole sink if you cover the extra holes with a deck plate, but a three-hole faucet will not fit a single-hole sink.
Shopping for one? See our guide: Replacing Kohler Kitchen Faucet Cartridge: 3 Best Picks (2026).
Gather these items before you begin:
- Adjustable wrench and basin wrench
- Bucket and towels
- Flashlight or headlamp
- Plumber’s putty or the gasket supplied with the new faucet
- Replacement supply lines if the old ones are cracked or stiff
Step-by-Step: Removing the Old Faucet
- Shut off the water. Turn the angle stops under the sink clockwise. If they are seized, shut off the main supply to the house.
- Open the faucet. Run the hot and cold taps to release pressure and drain remaining water into your bucket.
- Disconnect the supply lines. Place the bucket beneath the connections and loosen the nuts with your wrench. Keep a towel handy for drips.
- Remove the mounting nuts. Reach up under the sink with a basin wrench and unscrew the nuts that hold the faucet base to the sink. Pull the old faucet out from above.
- Clean the surface. Scrape off old putty or gasket residue so the new faucet seats flat.
Installing the New Kohler Faucet
Set the new faucet into the mounting holes, following the orientation shown in the included instructions. Install the gasket or apply a thin bead of plumber’s putty to the base, then press the faucet down firmly. Thread the mounting shanks and washers from below, tightening evenly so the faucet sits straight. Overtightening can crack a plastic base or deform the gasket, so snug the nuts and stop.
Connect the hot and cold supply lines to the matching stops. Tighten the connections by hand first, then a quarter turn with a wrench. Avoid forcing threaded fittings, especially on plastic components.
Testing for Leaks and Adjusting
Turn the water back on slowly at the angle stops. Open the faucet and let it run for a minute so air clears from the lines. Check each connection under the sink for drips, then look at the base where the faucet meets the countertop. If you see water, shut the supply off and tighten the nut or fitting in small increments.
Once the faucet is dry, run hot and cold water and confirm the handle moves smoothly through its full range. Check that the spray head, if you have one, retracts and returns properly.
Common Mistakes to Avoid
- Buying a faucet before measuring the sink’s hole count and spacing.
- Skipping the water shutoff and getting soaked when the line releases.
- Overtightening mounting nuts, which can crack the faucet base or sink.
- Reusing old supply lines that show stiffness, bulging or corrosion.
- Forgetting the deck plate when a single-hole faucet is going into a three-hole sink.
Recommended Gear
- Basin wrench: Its angled, long-reach jaws make it far easier to tighten the mounting nuts you cannot see from above. View on Amazon
- Braided stainless steel supply lines: These resist bursting better than rubber lines and are a common upgrade during faucet swaps. View on Amazon
- Plumber’s putty: It seals the faucet base against the countertop and is easy to clean up if you need to reposition the faucet. View on Amazon
For related guidance on specific models, see Kohler Kitchen Sink Faucet Guide: Choose, Install and Maintain One and Kohler Kitchen Faucet Spray Head Problems: Causes and Fixes (Step-by-Step). If you are replacing only the internal part rather than the whole unit, Replace Kohler Kitchen Faucet Cartridge: Step-by-Step Guide (2026) covers that process.
FAQ
Can I replace a Kohler faucet myself?
Yes, most homeowners can handle a straightforward swap with basic hand tools and a few hours. If the shutoff valves are seized or the old faucet is corroded in place, a licensed plumber can save time and avoid damage. Consult a professional if you find water damage under the sink.
Do I need a new sink to fit a different Kohler faucet?
Not always. A single-hole faucet can be mounted in a three-hole sink using a deck plate, but a three-hole faucet requires a sink with three matching holes. Measure hole spacing before buying.
How long does a faucet replacement take?
Most replacements take between one and three hours, depending on access under the sink and whether the supply lines need replacing. Allow extra time if you need to shut off the main water line.
Conclusion
Replacing a Kohler kitchen faucet comes down to confirming fit, shutting off the water, removing the old unit and sealing the new one carefully. Test thoroughly for leaks before you call the job finished. Take your time under the sink, and the new faucet should serve you well for years.
Related reading
- Moen vs Kohler Kitchen Faucet: 3 Best Picks Compared (2026)
- Kohler vs Delta Kitchen Faucet (2026): Which Is Better for Your Kitchen?
- Kohler Simplice Pull-Down Kitchen Faucet Review: Key Features Explained
Ready to choose one?
