We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Taking Out Kitchen Faucet: A Step-by-Step Guide for Beginners

Learn how taking out a kitchen faucet works, from shutting off water to disconnecting supply lines and lifting the old unit free. Clear steps for beginners.

Updated November 2026

Taking out a kitchen faucet is a manageable job for most homeowners with basic hand tools. You will shut off the water, disconnect the supply lines, release the mounting nuts under the sink, and lift the old faucet free. Plan on about an hour, and keep a bucket and towels nearby, since some water is always left in the lines.

Before You Start: Gather Tools and Shut Off the Water

Work with the sink cabinet doors open and the area under the sink cleared. Locate the two shutoff valves on the hot and cold supply lines and turn them clockwise until they stop. Then open the faucet to relieve pressure and drain the remaining water.

Shopping for one? See our guide: Delta Tap Kitchen Faucet Review: Key Features Explained.

  • Adjustable wrench or basin wrench
  • Bucket and old towels
  • Flashlight or headlamp
  • Plastic putty knife or scraper
  • Penetrating oil for stuck nuts
  • Replacement supply lines, if the old ones are cracked or brittle

Disconnect the Supply Lines and Mounting Hardware

Place the bucket under the connections, then loosen the compression nuts on each supply line. Use a second wrench on the valve body so you do not twist the shutoff valve. Once the lines are free, remove the spray hose connection if your faucet has one.

Next, release the mounting hardware. Most faucets are held by a mounting nut on threaded shanks, reached with a basin wrench since the space is tight. Some models use a metal bracket or clip underneath instead. If the nuts are seized, apply penetrating oil and wait 10 to 15 minutes before trying again.

Handling Corroded or Stubborn Nuts

Mineral buildup and age can fuse the nut to the shank. Tap the nut gently with a hammer and a block of wood to break the seal, then reapply oil. Avoid heavy force on the sink itself, since a cracked basin is a far bigger problem than a stuck nut.

Lift Out the Old Faucet and Clean the Surface

Lift the faucet straight up from the sink deck, working it gently side to side if it resists. Some faucets sit on a rubber gasket or plumber’s putty, so use the putty knife to scrape away old sealant. Clean the mounting surface with a damp cloth until it is smooth and dry, because a clean surface helps a new faucet seat properly.

Check the Sink and Decide What Comes Next

Before installing a replacement, measure the existing holes. Single-hole, three-hole and widespread layouts use different spacing, so the new faucet must match. Note the hole center spacing and the deck thickness, since these determine which models will fit. You can also review sizing guidance in the Three Hole Faucet Kitchen Guide: Setup, Sizing and Buying Tips to confirm your layout before buying.

  • Basin wrench: Reaches the mounting nuts in the tight space behind the sink basin, where a standard wrench cannot fit. View on Amazon
  • Penetrating oil: Loosens corroded threads and mineral-fused nuts so you avoid forcing them. View on Amazon
  • Flexible supply lines: Useful when the old lines are brittle or the connections are worn, so you can reconnect cleanly. View on Amazon

Common Mistakes to Avoid

  • Skipping the shutoff valves and leaving the water running, which floods the cabinet.
  • Forcing a seized nut without oil, which can crack the mounting shank or the sink.
  • Twisting the shutoff valve while loosening a supply line, which can break the valve.
  • Failing to photograph the connections, which makes reassembly harder.
  • Ignoring a leak after reconnecting; check each joint with a dry paper towel.

FAQ

Do I need to turn off the main water supply?

Usually no. The shutoff valves under the sink isolate the faucet, but if they are stuck or leak, shut off the main supply to the house.

Can I reuse the old supply lines?

Only if they are flexible, leak-free and show no cracks or corrosion. Replacing them is inexpensive insurance against future leaks.

What if the faucet will not come up?

Recheck for hidden mounting nuts or brackets, and reapply penetrating oil. If it still resists, a plumber can help without risking damage to the sink.

Conclusion

With the water off and the supply lines and mounting hardware released, the old faucet should lift out cleanly. Clean the sink surface, confirm the hole layout, and you are ready for the next step. If anything looks damaged or stuck, consult a licensed plumber.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Kitchen Bath Channel.