How to Change the Kitchen Sink Faucet: A Step-by-Step Guide (2026)
Learn how to change the kitchen sink faucet in a few hours with basic tools. Covers shutoff valves, disconnecting supply lines, mounting the new faucet and test
Updated November 2026
To change the kitchen sink faucet, you shut off the water, disconnect the old supply lines and mounting hardware, lift out the old unit, and install the new faucet following its included instructions. Most homeowners can finish the job in two to four hours with basic hand tools. The steps below cover preparation, removal, installation and leak testing.
Before You Start: Check Your Sink and Faucet Setup
Look under the sink first. Your new faucet needs to match the number of holes in your sink deck, which is usually one, three or four. A single-hole faucet sits on one opening, while a center-set faucet uses three holes and a widespread faucet uses three separate pieces. If you are unsure which style fits, the guide on How to Replace a Kitchen Faucet: A Step-by-Step Guide for Beginners explains how to identify hole configurations.
Shopping for one? See our guide: 6 Best Kitchen Sink Faucet Moen Models for Every Need (2026).
Also confirm whether your sink is drop-in or undermount, since that affects how the mounting nut is reached. Measure the distance from the sink deck to the underside of the counter if you are changing to a taller model.
Step-by-Step: Removing the Old Faucet
- Turn off the water supply valves under the sink by turning them clockwise until they stop. If the valves are stiff or do not shut off fully, shut off the main water supply to the house.
- Turn on the faucet to relieve pressure and let any remaining water drain.
- Place a bucket and towels under the sink to catch residual water.
- Disconnect the supply lines from the shutoff valves using an adjustable wrench. Hold the valve steady with a second wrench so the valve does not twist.
- Remove the mounting nuts or clips that hold the faucet to the sink deck. Working from below with a basin wrench makes this much easier in tight spaces.
- Lift the old faucet up and out. Clean any old plumber’s putty or gasket residue from the sink surface so the new faucet seats flat.
Installing the New Kitchen Sink Faucet
Read the manufacturer’s instructions before you begin, since mounting hardware and gasket placement vary by brand. Most new faucets include a base gasket or sealing plate. Set it in place, feed the supply lines through the hole, and position the faucet body on the deck.
From below, tighten the mounting nuts or fasteners evenly so the faucet sits straight and does not rock. Avoid overtightening, which can crack the sink or distort the gasket. Once the faucet is secured, connect the supply lines to the shutoff valves. Hand-tighten the connections first, then add a quarter turn with a wrench.
Testing for Leaks and Final Adjustments
Open the shutoff valves slowly, then turn on the faucet and let water run for a minute. Check every connection under the sink for drips. Run the hot and cold sides separately, and test the sprayer if your model has one. If you see a leak at a fitting, close the valve, tighten the connection slightly, and retest.
After the faucet runs clean, wipe the surface, check that the handle moves smoothly through its full range, and confirm the water temperature responds correctly. If a faucet seems to leak after installation, the troubleshooting steps in Moen Faucet Drips Kitchen: How to Find and Stop the Leak (Step-by-Step) can help identify the source.
Common Mistakes to Avoid
- Skipping the shutoff step and getting soaked when the supply lines come off.
- Buying a faucet with the wrong number of holes for your sink deck.
- Overtightening mounting nuts, which can crack a porcelain or composite sink.
- Reusing old supply lines that show corrosion or cracks. Replacing them is inexpensive insurance against leaks.
- Forgetting to test for leaks before closing the cabinet doors.
Recommended Gear
- Basin wrench: Reaches the mounting nuts in the tight space under the sink, where a standard wrench cannot fit. View on Amazon
- Adjustable wrench: Handles supply line nuts and shutoff valve connections of varying sizes. View on Amazon
- Plumber’s putty: Seals the sink deck around the base of the faucet to prevent water from seeping underneath. View on Amazon
FAQ
Do I need to turn off the main water to change a kitchen faucet?
Usually no, if the under-sink shutoff valves work. Turn them off first and test by running the faucet, and only shut off the main supply if the valves are stiff or leak.
How long does it take to change a kitchen sink faucet?
Most people finish in two to four hours, depending on access under the sink and whether the old faucet is seized to the deck. First-time installers should allow extra time.
Can I change a kitchen faucet myself, or should I hire a plumber?
A confident DIYer can handle the swap with basic tools. If you find corroded pipes, damaged valves or water damage under the sink, consult a licensed plumber before proceeding.
Conclusion
Changing a kitchen sink faucet comes down to shutting off the water, removing the old unit cleanly, and mounting the new one securely. Take your time with the hardware and leak test before you finish. With the right tools and a careful approach, the job is very manageable for most homeowners.
Related reading
- How to Replace a Kitchen Sink Faucet: A Step-by-Step Guide (2026)
- How to Replace Sink Faucet in Kitchen: A Step-by-Step Guide (2026)
Ready to choose one?
