How to Put In a Kitchen Faucet: A Step-by-Step Guide for Beginners
Learn how to put in a kitchen faucet with this step-by-step guide covering tools, supply lines, mounting, and leak checks so your install works the first time.
Updated November 2026
Learning how to put in a kitchen faucet comes down to four jobs: clear the old fixture, mount the new faucet through the sink holes, connect the supply lines, and test for leaks. Most standard single-handle or three-hole faucets can be installed in about one to two hours with basic hand tools. Confirm your sink’s hole count before you buy or remove anything.
Before You Start: Gather Tools and Check Your Sink
Measure the number of holes in your sink deck first. A single-hole faucet needs one opening, while a three-hole setup uses separate hot and cold valves plus a spout, and a four-hole sink often accepts a faucet with a side sprayer. Mismatched hole counts are the most common reason installs stall halfway through.
Shopping for one? See our guide: Delta Tap Kitchen Faucet Review: Key Features Explained.
Gather these tools and supplies:
- Adjustable wrench and basin wrench
- Plumber’s putty or silicone sealant (check the faucet manual for which to use)
- Bucket and old towels
- Flashlight
- New flexible supply lines, if the old ones are cracked or stiff
- Teflon tape for threaded connections
Step-by-Step: Removing the Old Faucet and Mounting the New One
Shut off the water and disconnect the old faucet
Turn off the shutoff valves under the sink, then open the faucet to relieve pressure. Place the bucket below and disconnect the supply lines, the water line, and the mounting nuts. Keep the old parts until the new faucet is fully working.
Clean the sink deck and dry-fit the new faucet
Scrape away old putty or sealant so the new gasket can sit flat. Set the faucet in the holes without sealant to confirm the base lines up with the deck and that the hoses reach the valves.
Seal and secure the faucet
Apply putty or silicone according to the manufacturer’s directions, set the faucet, and tighten the mounting nuts from below. Snug them evenly. Overtightening can crack the sink or the faucet base.
Connecting the Supply Lines and Testing for Leaks
Attach the supply lines to the shutoff valves, using Teflon tape on threaded fittings. Hand-tighten first, then add a quarter turn with a wrench. Slowly reopen the valves, run the faucet on hot and cold, and check every joint with a dry paper towel. Tighten only if you see moisture, and give each connection a full minute before deciding it is dry.
Recommended gear
- Basin wrench: reaches the mounting nuts in the tight space under the sink, where a standard wrench cannot. View on Amazon
- Plumber’s putty: creates a watertight seal between the faucet base and the sink deck when the manufacturer calls for it. View on Amazon
- Braided stainless supply lines: resist kinking and tend to hold up better than older rubber lines. View on Amazon
Common Mistakes to Avoid
- Skipping the dry fit, then discovering the hoses are too short after the sealant has set.
- Forgetting to shut off the water before disconnecting lines.
- Overtightening mounting nuts, which can crack ceramic or stone sinks.
- Using Teflon tape on compression fittings that call for a ferrule or gasket.
- Reusing old supply lines that show bulging, cracks, or corrosion.
If your sink or existing plumbing looks damaged, or the valves are seized, consult a licensed plumber before continuing.
FAQ
Do I need a plumber to install a kitchen faucet?
Many homeowners handle a basic swap themselves, especially when the existing holes match the new faucet. Call a licensed plumber if you need new holes drilled, the shutoff valves fail, or the drain assembly also needs work.
How long does a kitchen faucet installation take?
A straightforward replacement usually takes one to two hours. Allow extra time if old fittings are corroded or if you need to replace supply lines.
What if my new faucet has fewer holes than my sink?
Use the escutcheon plate included with many faucets to cover unused openings. If there is no plate, a matching sink cover or deck plate sold for that purpose will work.
Conclusion
Once you know your hole count, shut off the water, and seal the base correctly, learning how to put in a kitchen faucet becomes a manageable weekend task. Test every connection carefully before you walk away. For more background, see How to Replace a Kitchen Faucet: A Step-by-Step Guide for Beginners and Moen Faucet Drips Kitchen: How to Find and Stop the Leak (Step-by-Step).
Related reading
- Kitchen Faucet with Pullout Spray: How to Choose the Right One (2026)
- Kitchen Faucet with Pull-Out Sprayer: How to Choose and Install One (2026)
Ready to choose one?
