How to Fix a Bathroom Sink Faucet Leak: A Step-by-Step Guide
Learn how to fix a bathroom sink faucet leak in a few hands-on steps: find the source, shut off the water, replace the worn washer, O-ring or cartridge, and tes
Updated November 2026
To fix a bathroom sink faucet leak, you need to find where the water is escaping, shut off the supply, and replace the worn part causing it. Most leaks come from a washer, O-ring, cartridge or valve seat that has worn out over years of use. With basic hand tools and about an hour, you can usually stop the drip for good.
Identify Where the Leak Is Coming From
Before you take anything apart, figure out which kind of leak you have. A drip from the spout that continues after the handle is closed points to a worn washer, a cartridge or a valve seat. Water leaking from around the handle or base usually means a failed O-ring or packing nut. Water pooling under the sink suggests a loose supply line or a leaking connection.
Run the faucet for a few seconds, then dry the spout and handle with a towel. Watch where the new water first appears. That location tells you which part to inspect.
Shut Off the Water and Remove the Handle
Close the hot and cold supply valves under the sink by turning them clockwise until they stop. Open the faucet to drain remaining water and relieve pressure. Place a towel in the basin to protect the finish and keep small screws from going down the drain.
- Pry off the decorative cap on top of the handle with a flat-blade screwdriver.
- Remove the handle screw with a Phillips or hex key, depending on the faucet.
- Lift the handle off and unscrew the bonnet or packing nut with an adjustable wrench, wrapping the faucet body with a cloth to avoid scratches.
Replace the Worn Part
Once the internal parts are exposed, identify the type of faucet. Compression faucets use rubber washers and O-rings. Cartridge and ball faucets use a cartridge or ball assembly that is usually replaced as one unit. Take the worn part to a hardware store to match it exactly, since brand and size vary.
Compression Faucets
Unscrew the stem, then replace the rubber washer at the bottom and any O-rings on the stem. Check the valve seat inside the faucet body for pitting or grit. If the seat is rough, a seat-dressing tool can smooth it, or you can replace the seat.
Cartridge Faucets
Remove the retaining clip or nut that holds the cartridge in place and pull it straight out. Install the new cartridge with the tabs or index marks aligned as they were on the old one, then reinstall the clip. Lubricate new O-rings with plumber’s grease before seating them.
Reassemble, Test and Check for Leaks
Reassemble the faucet in reverse order, tightening nuts firmly but without forcing them. Slowly open the supply valves and run the faucet with the handle in the off position. Look for drips at the spout and around the base for several minutes.
If the faucet still leaks, recheck that the washer or cartridge seated correctly and that the valve seat is clean. Persistent leaks after a full rebuild can point to worn supply lines or a faucet that is near the end of its service life.
Recommended Gear
- Plumber’s grease helps seal new O-rings and lets stems move smoothly. View on Amazon
- Faucet cartridge puller can free a stuck cartridge without damaging the valve body. View on Amazon
- Assorted faucet washer and O-ring kit lets you keep matching parts on hand for different brands. View on Amazon
Common Mistakes to Avoid
- Forgetting to shut off both supply valves, which can leave water spraying when you loosen a nut.
- Installing a washer or cartridge from the wrong brand, which often leaks even when it looks similar.
- Overtightening packing nuts, which can crack the bonnet or damage the O-ring.
- Skipping the valve seat check, so a new washer wears out quickly against a rough seat.
- Reinstalling a cartridge with the index marks misaligned, which can cause stiff handles or continued leaking.
If you want to compare repair options before buying parts, the guide Bathroom Sink Faucet Drip Repair: 5 Best Kits for Every Fix (2026) covers complete kits. For a faucet that is worn beyond repair, Bathroom Sink Faucet Replacement: A Step-by-Step Guide for 2026 explains the swap process.
FAQ
Why does my bathroom sink faucet keep dripping after I fix it?
A new washer or cartridge may not be seated correctly, or the valve seat inside the faucet may be scratched. Recheck the installation and clean or dress the seat before reassembling.
Do I need to replace the whole faucet to stop a leak?
Usually not. Most leaks come from inexpensive internal parts such as washers, O-rings or cartridges. Replacing the whole faucet is only necessary if the body is cracked or the faucet is very old.
Can I fix a leak without turning off the water?
No. Shutting off the hot and cold supply valves under the sink is essential before removing any internal parts. Skipping this step can cause spraying water and a messy repair.
Conclusion
Stopping a bathroom sink faucet leak comes down to finding the source, shutting off the water, and replacing the worn washer, O-ring or cartridge. Take the old part with you when buying a replacement so the fit is exact. If the faucet still leaks after a careful repair, a qualified plumber can check the supply lines and valve body.
Related reading
- How to Fix Leaky Sink Faucet Bathroom: A Step-by-Step Guide
- Bathroom Tub Faucet Dripping: How to Find and Fix the Leak
- How to Repair a Bathroom Faucet Leak: A Step-by-Step Guide for Beginners
- How to Fix a Leaky Bathroom Tub Faucet: A Step-by-Step Guide
Ready to choose one?
