How to Fix a Dripping Bathroom Sink Faucet: A Step-by-Step Guide
Learn how to fix a dripping bathroom sink faucet in a few steps: shut off the water, identify the faucet type, replace the worn parts, and test the result.
Updated November 2026
To fix a dripping bathroom sink faucet, you shut off the water, identify your faucet type, and replace the worn part inside, usually a cartridge, washer, or O-ring. Most drips come from a single worn component, so the repair is often a one-hour job with basic hand tools. This guide walks through the process from start to finish.
Identify the Faucet Type Before You Start
The repair depends on how your faucet controls water flow. Most bathroom faucets use one of four mechanisms, and each one has a different wear point.
Shopping for one? See our guide: Bathroom Sink Faucet Drip Repair: 5 Best Kits for Every Fix (2026).
- Compression faucets have separate hot and cold handles that raise and lower a rubber washer against a valve seat. They are the most likely to drip from the handle base.
- Cartridge faucets use a single cylinder inside the body. A drip usually means the cartridge or its O-rings need replacing.
- Ball faucets use a slotted ball and several springs and seals. Drips here often come from worn rubber seats.
- Ceramic disc faucets use two ceramic plates. Drips usually come from grit trapped between the discs or a cracked disc.
If you are unsure which type you have, remove the handle cap and look at the stem. A single cylinder points to a cartridge, while two separate stems point to compression. Brand-specific guides, such as this Fix Moen Bathroom Faucet: A Practical Guide (2026), can help with model-specific parts.
Gather Tools and Shut Off the Water
Work with the water off and the drain plugged. A small rag in the sink drain keeps loose screws from disappearing. We also found Kohler Faucet Bathroom Sink: How to Choose, Install and Fix One useful on this point.
- Close the shutoff valves under the sink by turning them clockwise until they stop.
- Open the faucet to release remaining pressure and water.
- Gather a flathead screwdriver, adjustable wrench, Allen keys, plumber’s grease, and replacement parts that match your faucet brand.
- Take a photo of the parts as you disassemble them so you can reassemble correctly.
Replace the Worn Parts
Once the faucet is open, the repair itself is usually straightforward. Remove the handle, the retaining nut, and the internal part that is leaking.
For Compression Faucets
Unscrew the packing nut and remove the stem. Replace the rubber washer at the stem base and, if the valve seat is pitted, replace or resurface it with a seat-dressing tool. Apply plumber’s grease to the new washer before reinstalling.
For Cartridge and Ceramic Disc Faucets
Pull the cartridge straight out, noting its orientation. Replace it with a matching model, or clean the disc and replace the O-rings. Make sure the cartridge seats fully and the retaining clip is secure.
Reassemble, Test, and Confirm the Fix
Reassemble in reverse order, tighten nuts snugly without overtightening, and reopen the shutoff valves slowly. Run both hot and cold water for about thirty seconds, then close the handle fully and watch the spout for at least two minutes. A drip that stops within a few minutes of closing usually means the repair worked.
| Faucet Type | Most Common Drip Source | Usual Part to Replace |
|---|---|---|
| Compression | Worn washer or valve seat | Rubber washer, seat |
| Cartridge | Worn cartridge or O-rings | Cartridge, O-ring kit |
| Ball | Worn seats or springs | Seat and spring kit |
| Ceramic disc | Grit or cracked disc | Disc cartridge |
Common Mistakes
- Skipping the shutoff valves and getting sprayed when the handle comes off.
- Buying parts without matching the faucet brand and model.
- Overtightening the packing nut, which can crack the body or make the handle hard to turn.
- Forgetting to note the cartridge orientation before pulling it out.
- Replacing parts without checking the valve seat for pitting or mineral buildup.
Recommended Gear
- Plumber’s grease keeps rubber washers and O-rings supple and helps them seal. View on Amazon
- Faucet repair kit bundles common washers and O-rings for several faucet styles, which helps when you are unsure of the exact part. View on Amazon
- Adjustable wrench gives you the grip to loosen stubborn retaining nuts without rounding them. View on Amazon
FAQ
Why does my bathroom faucet keep dripping after I replace the washer?
The valve seat is often the cause. If it is pitted or corroded, a new washer will not seal properly, so resurface or replace the seat.
Can I fix a dripping faucet without turning off the main water supply?
Yes, if the sink has working shutoff valves under it. If those valves are stuck or leaking, shut off the main supply to your home first.
When should I call a plumber instead?
If the faucet body is cracked, the shutoff valves won’t close, or you find corrosion inside the supply lines, consult a licensed plumber before continuing.
Conclusion
Fixing a dripping bathroom sink faucet comes down to identifying the faucet type, replacing the worn internal part, and testing carefully. Keep the photos you took during disassembly handy and use parts that match your brand. With the water off and a methodical approach, most drips stop in a single afternoon.
Related reading
- How to Fix a Dripping Bathroom Faucet: A Step-by-Step Guide for Beginners
- How to Fix Leaky Sink Faucet Bathroom: A Step-by-Step Guide
- Bathroom Tub Faucet Dripping: How to Find and Fix the Leak
Ready to choose one?
