We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Change a Faucet in a Bathroom Sink: A Step-by-Step Guide

Learn how to change a faucet in a bathroom sink with this step-by-step guide covering shutoff valves, disconnecting supply lines, mounting and checking for leak

Updated November 2026

To change a faucet in a bathroom sink, you shut off the water, disconnect the old supply lines and mounting hardware, remove the old faucet, and install the new one with its gasket and nuts. Most swaps take one to two hours with basic hand tools, and the process is much the same whether your vanity has a single-hole or three-hole sink. Read the faucet manufacturer’s instructions first, since mounting details vary.

Before You Start: Shut Off the Water and Gather Tools

Close the hot and cold shutoff valves under the vanity by turning them clockwise until they stop. Then open the faucet to relieve pressure and let any residual water drain. Place a towel or small bucket under the valves, because a few tablespoons of water will remain in the supply lines.

Shopping for one? See our guide: 6 Best Vintage Brass Bathroom Faucet Picks for Period-Style Sinks (2026).

Gather these tools and supplies before you begin:

  • Adjustable wrench and basin wrench
  • Flashlight or headlamp
  • Plumber’s putty or silicone sealant, if your sink calls for it
  • Rag or towel
  • New faucet, supply lines and mounting hardware
  • Penetrating lubricant for stubborn nuts

How to Remove the Old Bathroom Sink Faucet

Start by disconnecting the supply lines from the shutoff valves. Use the adjustable wrench to loosen each nut, holding the valve steady so you don’t twist the pipe behind it. If a nut won’t budge after several minutes, apply penetrating lubricant, wait ten minutes and try again.

Next, remove the mounting nuts underneath the sink. Reach up with a basin wrench, since the space is tight and a standard wrench rarely fits. Once the nuts are off, lift the old faucet straight up. If it’s stuck to the sink, scrape away old putty or sealant with a plastic scraper rather than metal, which can scratch the finish.

How to Install the New Faucet

Clean the sink deck so the new faucet seats flat. If your faucet includes a gasket or uses putty, apply it according to the manufacturer’s directions. Insert the faucet through the holes and set it in place from above, then go underneath to fasten the mounting nuts or bracket.

Tighten the nuts evenly by hand first, then a quarter turn at a time with the wrench. Overtightening can crack the sink or distort the gasket, so snug is enough. Attach the supply lines to the faucet’s hot and cold connections. Hot is usually on the left and cold on the right, but confirm with the labels on your faucet.

Check for Leaks

Open the shutoff valves slowly, one at a time, while watching the connections. Turn on the faucet and run hot and cold water for about a minute. Look under the sink with a flashlight and dry the connections with a paper towel. A dry towel after a few minutes is a good sign that the joints are sealed.

Common Mistakes and Tips

  • Forgetting to close the shutoff valves, which leads to a flood on the vanity floor.
  • Using too much force on compression nuts, which can crack the valve or fitting.
  • Skipping the gasket or putty, which causes slow leaks at the sink deck.
  • Mixing up hot and cold lines. Check the labels before tightening.
  • Buying supply lines that are too short. Measure the distance from the valves to the faucet inlets first.

A basin wrench makes reaching mounting nuts far easier than a standard wrench. View on Amazon

Braided stainless steel supply lines are a common replacement choice when you’re already connecting new hardware. View on Amazon

Plumber’s putty helps seal the faucet base against the sink deck on sinks that call for it. View on Amazon

FAQ

Do I need to turn off the main water supply?

Usually no. The shutoff valves under the vanity are enough to isolate the faucet. If those valves are old or don’t close fully, shut off the main supply to the house before you start.

How long does it take to change a bathroom sink faucet?

Most people finish in one to two hours, depending on how stubborn the old nuts are and whether the supply lines need replacing. Allow extra time if the vanity is tight or the old faucet is corroded.

Can I install a faucet without plumber’s putty?

Some faucets come with a gasket and need no putty, while others call for it. Follow the manufacturer’s instructions. If you’re unsure, consult a licensed plumber for advice on your specific setup.

Conclusion

Changing a bathroom sink faucet comes down to shutting off the water, removing the old hardware carefully, and installing the new faucet with a secure, leak-free seal. Work slowly, check every connection and keep the manufacturer’s instructions nearby. With the right tools, this is a manageable weekend project.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Kitchen Bath Channel.