We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Install a New Bathroom Sink Faucet: A Step-by-Step Guide

Learn how to install a new bathroom sink faucet in about an hour, with the tools, shutoff steps, and connection tips you need to avoid leaks.

Updated November 2026

Learning how to install a new bathroom sink faucet is a manageable weekend job if you work in the right order. You will shut off the water, remove the old faucet, mount the new one on the sink, and connect the supply lines without leaks. Most homeowners with basic tools can finish in one to two hours.

Before You Start: Check Compatibility and Gather Tools

Look at your sink and vanity before buying or unboxing anything. Count the existing holes in the sink deck, since single-hole, three-hole (centerset), and widespread faucets each need a matching layout. Measure the distance between the supply valves under the sink as well. Many faucets include flexible supply lines, but you may need to buy longer lines if your valves sit far apart.

Shopping for one? See our guide: 6 Best Picks to Install New Faucet Bathroom Projects (2026).

Gather these tools and supplies before you begin:

  • Adjustable wrench and basin wrench
  • Plumber’s putty or a silicone gasket, depending on the faucet
  • Bucket and old towels
  • Flashlight
  • Replacement supply lines, if needed
  • Plumber’s tape (PTFE tape) for threaded connections

Step-by-Step: Remove the Old Faucet and Shut Off Water

Start by closing both shutoff valves under the sink by turning them clockwise until they stop. Then open the faucet to relieve remaining pressure and let the lines drain into your bucket. Disconnect the supply lines with your wrench, and place a bucket beneath them to catch residual water.

Next, remove the mounting nuts or clips holding the old faucet to the sink. A basin wrench reaches the nuts that sit in the tight space behind the basin. Lift the old faucet out and scrape away any old putty or gasket residue so the sink surface is clean and dry before you set the new unit.

Mount the New Faucet to the Sink

Follow the manufacturer’s instructions for your specific model, since mounting hardware varies. For most faucets, you will set a gasket or a bead of plumber’s putty around the base, then feed the faucet body through the holes. Tighten the mounting nuts from underneath, snugging them evenly rather than cranking one side down first. Overtightening can crack a porcelain or stone sink.

If your faucet has a deck plate, position it before tightening. Wipe away any squeezed-out putty right away, because it hardens quickly and is harder to remove later.

Connect the Supply Lines and Drain

Attach the supply lines to the faucet’s inlet shanks first, then to the shutoff valves. Hand-tighten each connection, then add a quarter to half turn with the wrench. Wrap threaded connections with PTFE tape in the direction the threads turn. Install the pop-up drain or drain assembly according to the instructions, and make sure the drain stopper moves freely.

Turn On the Water and Test for Leaks

Open the shutoff valves slowly, about halfway at first. Run the faucet on hot and cold for a minute to flush debris from the lines and aerator. Then check every connection under the sink with a dry paper towel. Any spot that shows moisture needs another quarter turn, not a full tightening. Let the faucet run for several minutes and recheck before you call the job finished.

  • Basin wrench: Its long, angled jaws reach mounting nuts in the tight space behind the sink, where a standard wrench cannot fit. View on Amazon
  • Braided stainless supply lines: These flexible lines are often easier to route than rigid tubing and are widely recommended for replacement connections. View on Amazon
  • PTFE thread seal tape: It creates a seal on threaded fittings and is inexpensive to keep on hand. View on Amazon

Common Mistakes

  • Skipping the shutoff check: Always confirm the valves are closed before disconnecting lines.
  • Overtightening mounting nuts, which can crack the sink.
  • Forgetting to flush the lines before testing, which can clog the new aerator.
  • Reversing the hot and cold connections, so check labels on the faucet.
  • Leaving putty residue behind, which prevents a proper seal.

FAQ

Do I need a plumber to install a bathroom sink faucet?

Most homeowners can handle a standard replacement with basic tools. If you find corroded shutoff valves, damaged supply lines, or a faucet that doesn’t match your sink holes, consult a licensed plumber.

How long does it take to install a new bathroom faucet?

A typical replacement takes one to two hours, longer if the old faucet is stuck or the shutoff valves are hard to turn. Plan for extra time if you need to replace supply lines.

Why is my new faucet dripping under the sink?

A slow drip usually points to a loose supply line connection or a missing washer. Tighten the connection another quarter turn, and recheck with a dry towel.

Conclusion

Installing a new bathroom sink faucet comes down to checking fit, shutting off water, mounting carefully, and testing every connection. Take your time with the nuts and fittings, and a leak-free result is well within reach. For related steps, see How to Install a New Faucet in Bathroom: A Step-by-Step Guide and Removing a Bathroom Sink Faucet: A Step-by-Step Guide for Beginners.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Kitchen Bath Channel.