We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Install a New Faucet in Bathroom: A Step-by-Step Guide

Learn how to install a new faucet in bathroom with this step-by-step guide covering shutoff valves, supply lines, mounting, and leak testing.

Updated November 2026

Learning how to install a new faucet in bathroom vanities is manageable for most homeowners with basic hand tools and a few hours. You will shut off the water, remove the old faucet, mount the new one, connect the supply lines, and test for leaks. The steps below assume a standard single-hole or three-hole sink.

Before You Start: Check Your Sink and Supplies

Confirm that the new faucet matches your sink’s hole count. A single-hole faucet fits a single opening, while a three-hole faucet needs spacing that matches the mounting pattern. Check the supply line connections too, since many faucets use standard 3/8-inch compression fittings, but some use different sizes.

Shopping for one? See our guide: 6 Best Picks to Install New Faucet Bathroom Projects (2026).

Step-by-Step Installation Process

Shut off the water and remove the old faucet

Close the angle stop valves under the sink, then open the faucet to release pressure. Disconnect the supply lines with an adjustable wrench, and loosen the mounting nuts or clips underneath. Lift the old faucet out and scrape away old plumber’s putty or silicone from the sink surface.

Prepare the sink and set the new faucet

Clean the mounting surface thoroughly. If the faucet manufacturer calls for a gasket or sealing pad, place it on the sink first. Feed the faucet through the hole or holes, and position it so the spout lines up with the bowl. Tighten the mounting hardware from below, snugging it evenly so the faucet sits straight without cracking the sink.

Connect the supply lines

Attach the hot and cold supply lines to the correct shutoff valves, usually marked with red and blue indicators. Hand-tighten each connection first, then give it a quarter turn with a wrench. Overtightening can crack a compression nut or damage the seal.

Turn on the water and test for leaks

Open the shutoff valves slowly, then run the faucet on hot and cold for about a minute. Check each connection under the sink with a dry paper towel. If you see moisture, tighten the fitting slightly and recheck.

Tools and Materials Checklist

  • Adjustable wrench and basin wrench
  • Plumber’s putty or the gasket supplied with the faucet
  • Flexible supply lines (if the new faucet does not include them)
  • Bucket and towels for residual water
  • Flashlight for working under the sink
  • Painter’s tape to protect the finish during tightening

Common Mistakes to Avoid

  • Skipping the water shutoff step and getting soaked when the faucet comes off.
  • Overtightening plastic nuts, which can crack and cause slow leaks.
  • Forgetting to check hot and cold lines are connected to the correct sides.
  • Not cleaning old putty, which leaves the new faucet sitting unevenly.
  • Testing for leaks only at the faucet base and missing the supply line joints.
  • A basin wrench makes it far easier to reach mounting nuts in tight vanity cabinets. View on Amazon
  • Braided stainless steel supply lines are a common upgrade that many owners prefer for durability. View on Amazon

If you are still choosing a fixture, our guide to Single Hole Faucet for Bathroom: 5 Best Picks Compared (2026) covers the options that fit one-hole sinks. For three-hole layouts, see Bathroom Faucet Three Hole: How to Choose and Install One (2026).

FAQ

Do I need a plumber to install a new bathroom faucet?

Most homeowners can handle the job with basic tools, as long as the shutoff valves work. If the valves are corroded or leak when you try to close them, consult a licensed plumber before proceeding.

How long does it take to install a new faucet in the bathroom?

For a first-timer, plan on one to two hours, including removing the old faucet and testing for leaks. Experienced installers often finish faster.

What if my new faucet has no supply lines?

Buy flexible supply lines that match your faucet’s connection size and your shutoff valves. Check the faucet packaging for the required fitting type before purchasing.

Conclusion

Installing a new bathroom faucet comes down to shutting off the water, mounting the fixture securely, and checking every connection for leaks. Take your time with the supply lines and nuts, and the job should go smoothly. Consult a professional if you encounter damaged valves or plumbing problems beyond the faucet itself.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Kitchen Bath Channel.