We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Repair Leaking Faucet in Kitchen: A Step-by-Step Guide for Beginners

Learn how to repair leaking faucet in kitchen with this step-by-step guide. Find the leak source, shut off water, replace worn parts, and stop drips for good.

Updated November 2026

Learning how to repair leaking faucet in kitchen fixtures usually takes one to two hours and a handful of basic tools. Most drips come from a worn washer, O-ring, cartridge or valve seat, and each of these can be replaced without calling a plumber. This guide walks you through identifying the source of the leak, shutting off the water, and swapping the failing part.

Identify Where the Leak Is Coming From

Before you take anything apart, figure out whether the water is dripping from the spout, around the base, or from the handle. A drip from the spout usually points to a worn cartridge, valve seat or washer. Water seeping from the base of the spout or around the handle usually means a failed O-ring or packing nut. Dry the faucet completely, then watch it for a few minutes to see exactly where the water appears. If you have a Moen model, the steps in Moen Faucet Drips Kitchen: How to Find and Stop the Leak (Step-by-Step) can help you match the symptom to the part.

Shopping for one? See our guide: 5 Best Kitchen Faucet Parts Price Pfister Options for Easy Repairs (2026).

Shut Off the Water and Remove the Handle

Close the hot and cold shutoff valves under the sink, then open the faucet to release any remaining pressure. Plug the drain so small screws or parts cannot fall into it. Next, remove the handle, which often hides a decorative cap and a set screw. Once the handle is off, you can reach the cartridge or valve assembly. If you are unsure how to pull the parts out, How to Take Kitchen Faucet Off: A Step-by-Step Guide for Beginners covers the removal process in detail.

Replace the Worn Parts

Once the cartridge or valve is exposed, use this sequence:

  1. Take a photo of the assembly so you remember how each part is oriented.
  2. Unscrew the retaining nut or clip and lift out the cartridge or stem.
  3. Compare the old part to a replacement from the same manufacturer. Matching the brand and model matters because internal dimensions vary.
  4. Replace the O-rings and seals, lightly coating them with plumber’s grease.
  5. Reassemble in reverse order, making sure the cartridge seats fully and the handle lines up with the hot and cold markings.

For compression-style faucets with a washer and seat, replace both the rubber washer and the brass seat if the seat shows pitting. A worn seat will keep leaking even with a new washer.

Test the Faucet and Check for Leaks

Turn the water supply back on slowly, then run the faucet at low and high flow. Check the spout, base and handle for at least five minutes. Tighten the packing nut or retaining nut only a quarter turn at a time if you see seepage, since overtightening can crack plastic parts or distort O-rings. If the leak continues after a new cartridge, confirm the cartridge is fully seated and that the inlet filters are clear of debris.

Common Mistakes

  • Skipping the shutoff valves and getting sprayed when the handle comes off.
  • Buying a generic cartridge that does not match the faucet brand and model.
  • Overtightening nuts, which can damage O-rings and create new leaks.
  • Forgetting to plug the drain, which lets small screws disappear.
  • Replacing only the washer when the valve seat is the real source of the drip.
  • Faucet repair kit: A kit with O-rings, washers and seals helps you replace several wear points in one trip to the store. View on Amazon
  • Plumber’s grease: Silicone-based grease keeps O-rings supple and makes reassembly smoother. View on Amazon
  • Adjustable wrench and basin wrench: A basin wrench reaches the retaining nuts that sit tight against the sink. View on Amazon

FAQ

Do I need to replace the whole faucet to stop a leak?

Usually not. Most leaks come from a worn cartridge, washer, O-ring or valve seat, and replacing that part restores a watertight seal. Replace the whole faucet only if the body is cracked or the model is no longer serviceable.

How do I know which replacement part to buy?

Remove the old part and bring it to the store, or look up the faucet brand and model number printed on the body or in the manual. Matching the manufacturer’s part number is the safest choice. For related fixes, see Moen Kitchen Faucet Tighten Handle: 4 Best Repair Parts Compared (2026).

Can a dripping faucet waste much water?

A steady drip can waste a surprising amount of water over a month, which is why fixing it promptly is worthwhile. If you are unsure about shutting off supply lines or working near water heater connections, consult a licensed plumber.

Conclusion

To repair a leaking kitchen faucet, find the leak source, shut off the water, and replace the worn cartridge, washer, O-ring or seat. Match the replacement part to your faucet brand, and test slowly once everything is back together. If the leak persists, a professional plumber can confirm the cause.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen & bathroom fixtures guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Kitchen Bath Channel.