Leaky Faucet Repair Bathroom Sink: 5 Steps to Stop the Drip (2026)
Learn leaky faucet repair for a bathroom sink in five steps: find the cause, shut off water, replace the worn part, and stop the drip for good.
Updated November 2026
Leaky faucet repair on a bathroom sink usually comes down to one worn part: a washer, O-ring, cartridge or valve seat. In most cases you can shut off the water, identify the faulty component, replace it and test the faucet within an hour using basic hand tools. This guide walks through that process and explains how to avoid the mistakes that cause repeat leaks.
Find Out Which Type of Faucet You Have
The repair depends on the faucet design, so identify it first. Most bathroom sink faucets fall into one of four groups:
Shopping for one? See our guide: Bathroom Leaky Faucet Repair Kits: 7 Best Picks Compared (2026).
- Compression faucets have separate hot and cold handles and use rubber washers that press against a valve seat. They usually drip from the spout when the handle is off.
- Cartridge faucets use a single handle and a cylinder-shaped cartridge. Leaks often show up at the base of the spout or around the handle.
- Ball faucets have one handle on a dome-shaped cap and use several rubber seals and springs.
- Ceramic disc faucets use two ceramic discs. They seldom need repair, but grit can cause a drip that a cartridge swap or disc cleaning will fix.
If you are unsure, remove the handle cap and look at the stem or cartridge. Take a photo before you disassemble anything so you can match parts later. For a broader overview of common failure points, see How to Repair a Leaky Bathroom Sink Faucet: A Step-by-Step Guide. If you want more background, see Bathroom Sink Faucet Repair Kit: 7 Best Picks Compared (2026).
Shut Off the Water and Remove the Handle
Close the hot and cold angle stops under the sink, then open the faucet briefly to release any trapped pressure. Plug the drain so small screws do not disappear down it.
- Pry off the decorative cap on the handle with a flathead screwdriver or a thin putty knife.
- Remove the handle screw, usually a Phillips or hex screw. Lift the handle straight up.
- Unscrew the packing nut or retaining nut with an adjustable wrench, wrapping the jaws in tape to protect the finish.
- Lift out the stem, cartridge or valve assembly. Keep the parts in order on a towel.
If the handle is stuck, do not force it. Penetrating oil and a few minutes of patience usually work. For tougher cases, the walkthrough in How to Remove Bathroom Sink Faucet Handle Without Screws: A Step-by-Step Guide covers alternative release methods.
Replace the Worn Parts
Once the assembly is out, inspect it. Look for flattened or cracked rubber washers, pitted brass seats, torn O-rings and mineral crust. Replace any part that looks damaged rather than cleaning it, because worn rubber rarely seals again.
| Symptom | Likely cause | Fix |
|---|---|---|
| Drip from spout when off | Worn washer or valve seat | Replace washer; resurface or replace seat |
| Leak at base of spout | Failed O-ring | Replace O-rings |
| Leak around handle | Worn packing or stem seal | Replace packing or stem |
| Drip with one-handle faucet | Worn cartridge | Replace cartridge |
Bring the old parts to a hardware store or use the manufacturer’s model number to order exact replacements. Matching the brand matters, since sizes and shapes vary between makers. Many people buy a complete repair kit for their faucet type, which avoids a second trip. For kit options, see Bathroom Faucet Repair Kits: How to Fix a Leaky Faucet in 6 Steps.
Reassemble and Test the Faucet
Reverse the disassembly order. Apply a light coat of plumber’s grease to O-rings and cartridge seals, but keep grease away from the water path. Tighten nuts snugly without overtightening, since overtightening cracks washers and can distort cartridges.
Open the angle stops slowly and check for leaks at the base and handle before you run the water. Turn the faucet on and off several times and watch the spout closely. A slow drip after a few minutes usually means the seat is still damaged or the cartridge is not fully seated.
Common Mistakes to Avoid
- Skipping the water shutoff, which leads to spraying and lost parts.
- Reusing a worn washer because it looks intact. Flexible rubber can look fine and still leak.
- Mixing up hot and cold stems. Note which side each one came from.
- Overtightening the packing nut, which can crack the body or damage new seals.
- Ignoring a worn valve seat. A new washer will not stop a drip if the seat is pitted.
Recommended gear
- Plumber’s grease keeps O-rings flexible and helps the parts slide smoothly during reassembly. View on Amazon
- Adjustable wrench gives you the grip needed to loosen packing nuts without rounding them. View on Amazon
- Faucet cartridge puller helps remove stubborn cartridges that will not come out by hand. View on Amazon
FAQ
How long does a bathroom sink faucet repair usually take?
Most single-handle or compression repairs take about 30 to 60 minutes once you have the right parts. Stuck handles or corroded valves can add more time.
Can I repair the faucet without shutting off the main water supply?
Yes, in most homes the angle stops under the sink are enough. If they are old and do not close fully, shut off the main supply to be safe.
When should I call a plumber instead?
Call a licensed plumber if the valve body is cracked, the supply lines are corroded, or the leak continues after new parts are installed. Consult a professional if you smell gas or see water damage behind the vanity.
Conclusion
Leaky faucet repair on a bathroom sink is manageable when you identify the faucet type, replace worn parts instead of cleaning them, and test carefully after reassembly. Keep the old parts for reference and work slowly to avoid cracks and lost screws. With the right replacement part, most drips stop for good in a single afternoon.
Related reading
Ready to choose one?
