Replace Kohler Kitchen Faucet: A Step-by-Step Guide for Beginners
Learn how to replace a Kohler kitchen faucet step by step, from shutting off the water to testing for leaks. A clear beginner guide with tips to avoid common mi
Updated November 2026
To replace a Kohler kitchen faucet, you shut off the water supply, disconnect the old unit, mount the new faucet on the sink, and reconnect the supply lines. Most homeowners can finish the job in one to two hours with basic hand tools. The steps below cover the process for a typical deck-mounted Kohler faucet, with notes on where the exact method can vary by model.
Before You Start: Check Your Sink and Faucet
Look under the sink first. Confirm the number of holes in your sink deck, since a single-hole, three-hole or four-hole setup determines which replacement faucets will fit. Check whether your current faucet is held in place with a mounting nut from below or a plate and screws. Kohler lists mounting requirements in each product’s installation guide, so match the new faucet’s hole configuration to what you already have.
Shopping for one? See our guide: Kohler Industrial Kitchen Faucet: 6 Best Picks for Pro-Style Kitchens (2026).
Step-by-Step Replacement Process
Shut Off the Water and Drain the Lines
Close the shutoff valves under the sink, usually one for hot and one for cold. Then turn on the faucet to release remaining pressure and let the lines drain.
Disconnect the Old Faucet
Place a towel and bucket under the sink. Disconnect the supply lines with a basin wrench or adjustable wrench, and detach any spray hose or pull-out head. Loosen the mounting nuts or plate underneath, then lift the old faucet out from above.
Install the New Faucet
Clean the sink surface so the new gasket or base seals evenly. Set the new faucet through the holes, add the included gasket, and tighten the mounting hardware from below. Keep the faucet centered and square to the sink before final tightening. Some Kohler models use a deck plate; if yours does, set the plate first.
Connect the Supply Lines and Test
Attach the supply lines to the matching hot and cold valves. Hand-tighten first, then add a quarter turn with a wrench, taking care not to overtighten plastic fittings. Open the valves slowly, run the faucet, and check each connection for drips.
Tools and Supplies Checklist
- Adjustable wrench and basin wrench
- Bucket and towels
- Phillips and flathead screwdrivers
- Plumber’s putty or the gasket supplied with the faucet
- Replacement supply lines, if the old ones are worn
- Flashlight for working under the sink
Common Mistakes to Avoid
- Skipping the step of shutting off the water, which leads to spray and flooding.
- Buying a faucet with the wrong number of holes for your sink deck.
- Overtightening supply line nuts, which can crack plastic fittings or strip threads.
- Forgetting to flush the new lines before testing, which can leave debris in the aerator.
- Leaving the faucet unsecured while tightening, which can shift the unit out of alignment.
Recommended Gear
A basin wrench makes reaching the mounting nuts behind the sink much easier than a standard wrench. View on Amazon
A flexible inspection light helps you see mounting hardware and supply connections in the tight space under the cabinet. View on Amazon
Plumber’s putty seals the base of the faucet to the sink surface, especially on sinks without a built-in gasket. View on Amazon
FAQ
Can I replace a Kohler kitchen faucet myself?
Yes, many homeowners handle it with basic hand tools and a few hours of time. If the supply lines or shutoff valves are corroded or leaking, consider consulting a licensed plumber.
How do I know which replacement faucet fits my sink?
Count the holes in your sink deck and check the mounting style under the sink. Match the new faucet’s hole configuration and installation requirements to what you have.
Do I need to replace the supply lines when I replace the faucet?
Not always, but it is a good idea if the existing lines are old, stiff or showing signs of leaks. New lines are inexpensive insurance against a slow leak under the cabinet.
Conclusion
Replacing a Kohler kitchen faucet comes down to shutting off the water, removing the old unit, mounting the new one and testing every connection. Checking your sink’s hole count before you start prevents most problems. Take your time with the fittings, and check for leaks before closing the cabinet.
Related reading
- Replace Kohler Kitchen Faucet Cartridge: Step-by-Step Guide (2026)
- Kohler Kitchen Faucet Spray Head: How to Replace or Fix It (2026)
- White Kitchen Faucet Kohler: How to Choose, Match and Care for One (2026)
- Replacing Kohler Kitchen Faucet: A Step-by-Step Guide for Beginners
- Replacing Kohler Kitchen Faucet Cartridge: 3 Best Picks (2026)
- Removing Kohler Kitchen Faucet: A Step-by-Step Guide for Beginners
Ready to choose one?
